| (not shown) | Oil Drain Tube for GX120-GX200, 10mm | Stop making a mess! This oil drain tube makes changing your oil easy. Simply remove your oil drain plug and install the metric threaded end into...Stop making a mess! This oil drain tube makes changing your oil easy. Simply remove your oil drain plug and install the metric threaded end into your engine block. Changing oil has never been so easy!... [+]
Click here for more info | $38.65
$29.85 |  | | - |
| (not shown) | Predator 6.5 HP Gas Engine | Generic version of Honda GX style engine. Incredible sale on this Predator 6.5 HP (212cc) gasoline engine! Save a bundle by replacing your old...Generic version of Honda GX style engine. Incredible sale on this Predator 6.5 HP (212cc) gasoline engine! Save a bundle by replacing your old Honda 5 or 6.5 HP engine with this one! The engine has gas-saving overhead valves for cooler, cleaner performance and longer life. The horizontal shaft is ball-bearing mounted, making this gas engine an ideal replacement for most standard engine configurations. Features a durable cast iron cylinder making it the perfect replacement engine for a lawn mower, log-splitter, air compressor, pressure washer and many, many other types of equipment. *90 day warranty. Limited offer*... [+]
Click here for more info | |  | (X) | SOL
No Info |
| 00011 | Pilot Valve | Pilot valve/check valve/unloader valve. 1/2" Compression Inlet, 1/2" FPT outlet. The brains of your compressor. Tells motor when to idle and go to...Pilot valve/check valve/unloader valve. 1/2" Compression Inlet, 1/2" FPT outlet. The brains of your compressor. Tells motor when to idle and go to full throttle. Unloads pump @ 125psi. The pilot/unloader valve controls the airflow from your pump to your tank, and also controls your engine speed, together with the throttle/idle control valve. It acts as the “brain” of your compressor. The valve pressure settings (cut-in and cut-out pressures) is almost always pre-set at the factory, but these settings are also adjustable. Replace if it leaks, chatters, or no longer cuts the unit in or out at the required pressure. There are many types and configurations of pilot valves: some have built-in check valves and unloader ports, depending on the configuration of the unit.... [+] | $94.19 |  | | - |
| 00014 | Bullwhip Throttle Control 24" Long Cable | Used on compressors with external unloading devices and engines 6.5 hp or below. The throttle/idle control assembly is used on gas-powered air...Used on compressors with external unloading devices and engines 6.5 hp or below. The throttle/idle control assembly is used on gas-powered air compressors, in conjunction with the pilot/unloader valve. This assembly connects to the throttle plate/carburetor of the engine to shift from idle to high speed and vice versa. There are generally two different types of throttle assemblies, those with a cable (“bullwhip”) and those with a hollow, nylon tube (“airline”). The Valve itself can attach to the engine throttle plate or thread into the pilot/unloader valve. The air line or cable connects the two and actuates the throttle/governor on the engine at specific pressures to control the speed of the engine.... [+] | $24.61 |  | | - |
| 00017 | Belt | Replace if worn. 4L490, use with model CT5090816 Replace your belt if it is frayed, starting to dry rot, or if too loose. | $14.05 | | | - |
| 00032A | Drain Cock, 1/4" | 1/4" MPT Brass (measures 1/2" on OD). Prevent your tank from rusting out. A simple but essential part, the drain cock (or valve) threads into your...1/4" MPT Brass (measures 1/2" on OD). Prevent your tank from rusting out. A simple but essential part, the drain cock (or valve) threads into your tank(s) and allows you to drain the tank(s) of water and moisture. Most are 1/8” or 1/4” male NPT and have either a knurled-style knob or wing nut to open/close the valve. Since most are brass or steel, they will rust over time and should be replaced as soon as they start to leak. Be sure to drain the tank after every extended use, as it can save your expensive tank from developing leaks.... [+]
Click here for more info | $5.44 |  | | - |
| 00032H | FOOT RUBBER | Keep your unit from sliding all around your vehicle or floor.
3/4" Height, 1 1/2" Diameter | $4.89 |  | | - |
| 00033A | Pressure Gauge | 0-200 PSI, 1/4" MPT, BACK MOUNT, 1.61" Face. Plastic face w/ metal back. A pressure gauge measures air pressure in the air tank and the pressure...0-200 PSI, 1/4" MPT, BACK MOUNT, 1.61" Face. Plastic face w/ metal back. A pressure gauge measures air pressure in the air tank and the pressure to the line from the air regulator. Be sure your gauges are accurate; if it is reading the pressure inaccurately it can damage the pump and other components and if the safety valve fails, the tank could explode. Moisture rusts/damages the gauge over time so they must be periodically replaced. Gauges can be air filled or liquid-filled.... [+] | $9.95 |  | | - |
| 00033D | Safety Valve, 150 PSI | If your valve leaks below the pressure listed on the side of the valve, replace this vital safety feature. A safety relief valve can save lives!...If your valve leaks below the pressure listed on the side of the valve, replace this vital safety feature. A safety relief valve can save lives! It keeps your tank from bursting should your pressure switch stop working. The Valve has a male thread and is set for a specific PSI at the factory. Usually, you want a valve rated 30 PSI higher than your pressure switch cut-out pressure.... [+] | $21.69 |  | | - |
| 00041 | Pressure Gauge | 0-200 PSI, 1/4" MPT, BOTTOM MOUNT, 2" Face. Replace after 5 years as they weaken and give improper readings. A pressure gauge measures air...0-200 PSI, 1/4" MPT, BOTTOM MOUNT, 2" Face. Replace after 5 years as they weaken and give improper readings. A pressure gauge measures air pressure in the air tank and the pressure to the line from the air regulator. Be sure your gauges are accurate; if it is reading the pressure inaccurately it can damage the pump and other components and if the safety valve fails, the tank could explode. Moisture rusts/damages the gauge over time so they must be periodically replaced. Gauges can be air filled or liquid-filled.... [+] | $13.06
$10.45 |  | | - |
| 00043 | Regulator, 3/8" | Norgren Regulator. 3/8inch inlet and outlet. 250 lbs. max psi. Two 1/4inch ports available on either side of regulator for gauge location.(Gauge...Norgren Regulator. 3/8inch inlet and outlet. 250 lbs. max psi. Two 1/4inch ports available on either side of regulator for gauge location.(Gauge sold separately below) Don't ruin your equipment, supply just the right amount of PSI to your tools with the regulator. A pressure regulator can be used on portable and stationary units and installs in-line. Don't forget your gravity water/particulate filter so you have clean, dry air to your line. Replace this if you can no longer regulate the exact amount of pressure you need to your line, or if it leaks. Be sure to check the accuracy of your regulator gauge periodically.... [+] | $39.71 |  | | - |
