| (not shown) | Replacement Element for (#1-4) Filter Assby. | Generic replacement filter element, fits all "FS-14" Assemblies. 4.25"OD x 3"ID x 2 3/8" Height. Replace every 3-4 months if air compressor is...Generic replacement filter element, fits all "FS-14" Assemblies. 4.25"OD x 3"ID x 2 3/8" Height. Replace every 3-4 months if air compressor is used frequently. A dirty filter can cause damage to the pump's valves, clog your check valve and reduce the CFM output of the compressor. Always keep an extra handy! A clean air filter is essential to the performance of an air compressor. Keep extras on hand as you will inevitably replace it, sometimes often (if used in a contractor or shop application). Some filters have paper elements like automotive air filters, some are simply foam or felt mediums. The filter installs into the inlet side of the pump head and filters out particulates that can damage the pump. Replace every three months or sooner (if used in a shop or jobsite), or whenever you change the oil.... [+] | $10.28 |  | | - |
| (not shown) | Rolair K24 Pump Rebuild Kit (Rings, Valves, Gaskets, Filter, Oil) | Includes most needed parts for full rebuild.
Kit contains: Gasket Set, Oil Sight Glass, Oil Breather/Dipstick, Rings, Air Filter, Reed Valves...Includes most needed parts for full rebuild.
Kit contains: Gasket Set, Oil Sight Glass, Oil Breather/Dipstick, Rings, Air Filter, Reed Valves and Blended Synthetic Compressor Oil. (Order 2 pair of bearing inserts if you hear rod knocking). A clean air filter is essential to the performance of an air compressor. Keep extras on hand as you will inevitably replace it, sometimes often (if used in a contractor or shop application). Some filters have paper elements like automotive air filters, some are simply foam or felt mediums. The filter installs into the inlet side of the pump head and filters out particulates that can damage the pump. Replace every three months or sooner (if used in a shop or jobsite), or whenever you change the oil.... [+] | $167.75 |  | | - |
| 2400VK24 | Valveplate Assembly | Includes both valveplates, valves, and all three gaskets. Poor performance, or does air leak out of the intake air filter while the unit is...Includes both valveplates, valves, and all three gaskets. Poor performance, or does air leak out of the intake air filter while the unit is running? This is probably the problem. Damaged/sticking valves is a common issue when you have low compression, and can also cause the motor/engine to stall and too much pressure in the pump’s crankcase. Be sure to clean the head and cylinder very well so as to remove all of the old gasket material and build-up (carbon and rust) when re-installing.... [+] | $201.88 | | | - |
| 30204610CH | Crankshaft | If your crank is grooved, replace it to ensure that your rebuild will not be in vain. If there are only surface deposits of aluminum from the...If your crank is grooved, replace it to ensure that your rebuild will not be in vain. If there are only surface deposits of aluminum from the bearings, then remove them with a soft wire brush and then polish your crank. The crankshaft translates rotational motion to reciprocating motion in a compressor pump. A crankshaft has “journals”, where the connecting rods ride on. A crank can be damaged by running the pump too low on oil, or if the drive belt is too tight. Make sure the output shaft (where the pulley installs) is not warped, and if you hear knocking, stop the unit immediately and disassemble the pump. When conrods seize onto the crankshaft, the journals must be polished of all aluminum (or iron) deposits before new conrods are installed. If pitted deeply, the crankshaft must be replaced.... [+] | $171.70 |  | | - |
| 30300030CH | Ball Bearing | Crankcase Ball Bearing, front end-cap. Bearings allow the compressor pump and motor/engine to run smoothly and reduce friction between moving...Crankcase Ball Bearing, front end-cap. Bearings allow the compressor pump and motor/engine to run smoothly and reduce friction between moving parts. Bearings can be sealed or open. There are generally two types of bearings found in air compressors, ball bearings and roller bearings. Bearings wear out periodically so If you hear metal grinding, the bearing(s) may need to be replaced.... [+] | $20.95 | | | - |
| 30300040CH | Seal | Seal for crank | $10.40 | | | - |
| 30400830CH | Bearing Carrier | Bearings allow the compressor pump and motor/engine to run smoothly and reduce friction between moving parts. Bearings can be sealed or open.... Bearings allow the compressor pump and motor/engine to run smoothly and reduce friction between moving parts. Bearings can be sealed or open. There are generally two types of bearings found in air compressors, ball bearings and roller bearings. Bearings wear out periodically so If you hear metal grinding, the bearing(s) may need to be replaced.... [+] | $36.53 | | | - |
| 30400860CH | Bearing Carrier | Bearings allow the compressor pump and motor/engine to run smoothly and reduce friction between moving parts. Bearings can be sealed or open.... Bearings allow the compressor pump and motor/engine to run smoothly and reduce friction between moving parts. Bearings can be sealed or open. There are generally two types of bearings found in air compressors, ball bearings and roller bearings. Bearings wear out periodically so If you hear metal grinding, the bearing(s) may need to be replaced.... [+] | $30.67 | | | - |
| 30500050CH | Gasket | Gaskets provide a seal between the pump’s components, such as the oil pan, crankcase, cylinder, valve plate(s) and head (as well as the... Gaskets provide a seal between the pump’s components, such as the oil pan, crankcase, cylinder, valve plate(s) and head (as well as the intercooler & aftercooler). Gaskets can be made from metal, cork, silicone, rubber, fiberglass or Teflon. It’s common for gaskets to “blow out” and leak, as debris in the head and back-pressure can damage them. When replacing, clean all old gasket material from the components, and install dry. Tighten the bolts to the correct torque setting for your unit. Having a clean air filter will also minimize gasket damage.... [+] | $6.95 | | | - |
| 30500130CH | Oil Site Gauge Gasket | Replace this gasket when replacing oil site gauge. A pressure gauge measures air pressure in the air tank and the pressure to the line from the...Replace this gasket when replacing oil site gauge. A pressure gauge measures air pressure in the air tank and the pressure to the line from the air regulator. Be sure your gauges are accurate; if it is reading the pressure inaccurately it can damage the pump and other components and if the safety valve fails, the tank could explode. Moisture rusts/damages the gauge over time so they must be periodically replaced. Gauges can be air filled or liquid-filled.... [+] | $3.98 |  | | - |
| 30500150CH | Gasket | Gaskets provide a seal between the pump’s components, such as the oil pan, crankcase, cylinder, valve plate(s) and head (as well as the... Gaskets provide a seal between the pump’s components, such as the oil pan, crankcase, cylinder, valve plate(s) and head (as well as the intercooler & aftercooler). Gaskets can be made from metal, cork, silicone, rubber, fiberglass or Teflon. It’s common for gaskets to “blow out” and leak, as debris in the head and back-pressure can damage them. When replacing, clean all old gasket material from the components, and install dry. Tighten the bolts to the correct torque setting for your unit. Having a clean air filter will also minimize gasket damage.... [+] | $6.95 |  | | - |
| 3050016ACH | Oil Breather Gasket | 3/8" gasket for oil breather. The oil breather/dipstick allows you to check the oil level in the pump, as well as allow to allow the crankshaft to...3/8" gasket for oil breather. The oil breather/dipstick allows you to check the oil level in the pump, as well as allow to allow the crankshaft to “breathe” through the vent in the breather. If the crankcase didn’t have a breather, too much pressure would inevitably build up in the crankcase and would cause oil to leak from the pump and damage its components. Make sure the vent isn’t clogged.... [+] | $4.88 |  | | - |
| 30501490CH | Aftercooler Tube Gasket | If leaking occurs around your aftercooler supply line at the head, replace this gasket. Gaskets provide a seal between the pump’s components,...If leaking occurs around your aftercooler supply line at the head, replace this gasket. Gaskets provide a seal between the pump’s components, such as the oil pan, crankcase, cylinder, valve plate(s) and head (as well as the intercooler & aftercooler). Gaskets can be made from metal, cork, silicone, rubber, fiberglass or Teflon. It’s common for gaskets to “blow out” and leak, as debris in the head and back-pressure can damage them. When replacing, clean all old gasket material from the components, and install dry. Tighten the bolts to the correct torque setting for your unit. Having a clean air filter will also minimize gasket damage.... [+] | $6.95 |  | | - |
| 30502400CH | O-ring, Intercooler | O-Ring, bottom of intercooler (two required). O-rings can be made from a variety of materials including polyurethane, silicone and neoprene....O-Ring, bottom of intercooler (two required). O-rings can be made from a variety of materials including polyurethane, silicone and neoprene. O-rings provide a seal between two components to keep out air or fluid. New o-rings must be lubricated with grease when installed.... [+] | $6.95 | | | - |
| 30502500CH | O-ring, Intercooler | O-ring for intercooler (top). Two required. O-rings can be made from a variety of materials including polyurethane, silicone and neoprene. O-rings...O-ring for intercooler (top). Two required. O-rings can be made from a variety of materials including polyurethane, silicone and neoprene. O-rings provide a seal between two components to keep out air or fluid. New o-rings must be lubricated with grease when installed.... [+] | $7.53 | | | - |
| 30504630CH | Gasket | Gaskets provide a seal between the pump’s components, such as the oil pan, crankcase, cylinder, valve plate(s) and head (as well as the... Gaskets provide a seal between the pump’s components, such as the oil pan, crankcase, cylinder, valve plate(s) and head (as well as the intercooler & aftercooler). Gaskets can be made from metal, cork, silicone, rubber, fiberglass or Teflon. It’s common for gaskets to “blow out” and leak, as debris in the head and back-pressure can damage them. When replacing, clean all old gasket material from the components, and install dry. Tighten the bolts to the correct torque setting for your unit. Having a clean air filter will also minimize gasket damage.... [+] | $14.89 | | | - |
| 30504740CH | Gasket | Gaskets provide a seal between the pump’s components, such as the oil pan, crankcase, cylinder, valve plate(s) and head (as well as the... Gaskets provide a seal between the pump’s components, such as the oil pan, crankcase, cylinder, valve plate(s) and head (as well as the intercooler & aftercooler). Gaskets can be made from metal, cork, silicone, rubber, fiberglass or Teflon. It’s common for gaskets to “blow out” and leak, as debris in the head and back-pressure can damage them. When replacing, clean all old gasket material from the components, and install dry. Tighten the bolts to the correct torque setting for your unit. Having a clean air filter will also minimize gasket damage.... [+] | $10.40 | | | - |
| 30504760CH | Gasket | Gaskets provide a seal between the pump’s components, such as the oil pan, crankcase, cylinder, valve plate(s) and head (as well as the... Gaskets provide a seal between the pump’s components, such as the oil pan, crankcase, cylinder, valve plate(s) and head (as well as the intercooler & aftercooler). Gaskets can be made from metal, cork, silicone, rubber, fiberglass or Teflon. It’s common for gaskets to “blow out” and leak, as debris in the head and back-pressure can damage them. When replacing, clean all old gasket material from the components, and install dry. Tighten the bolts to the correct torque setting for your unit. Having a clean air filter will also minimize gasket damage.... [+] | $18.21 | | | - |
| 30504770CH | Gasket | Gaskets provide a seal between the pump’s components, such as the oil pan, crankcase, cylinder, valve plate(s) and head (as well as the... Gaskets provide a seal between the pump’s components, such as the oil pan, crankcase, cylinder, valve plate(s) and head (as well as the intercooler & aftercooler). Gaskets can be made from metal, cork, silicone, rubber, fiberglass or Teflon. It’s common for gaskets to “blow out” and leak, as debris in the head and back-pressure can damage them. When replacing, clean all old gasket material from the components, and install dry. Tighten the bolts to the correct torque setting for your unit. Having a clean air filter will also minimize gasket damage.... [+] | $14.89 | | | - |
| 31004620CH | Flywheel | Replace if a spoke if cracked or it is slipping on the crankshaft. The flywheel is the compressor pump’s pulley, which the belt attaches to and...Replace if a spoke if cracked or it is slipping on the crankshaft. The flywheel is the compressor pump’s pulley, which the belt attaches to and drives the crankshaft. Be sure the flywheel and motor/engine pulley is aligned, as a misaligned pulley and flywheel can damage the pump and motor/engine. Replace if cooling fins are missing. Most flywheels have a specific rotation (usually C.C.W. when looking directly at the flywheel) so be sure the flywheel is installed correctly when replacing it to efficiently cool the pump.... [+] | $182.73 | | | - |
| 31100210CH | Bearing Inserts (order 2 for Both Rods) | If you start to hear knocking from your pump, then you need to replace your bearing inserts. Check crank to make sure it is not damaged. Bearings...If you start to hear knocking from your pump, then you need to replace your bearing inserts. Check crank to make sure it is not damaged. Bearings allow the compressor pump and motor/engine to run smoothly and reduce friction between moving parts. Bearings can be sealed or open. There are generally two types of bearings found in air compressors, ball bearings and roller bearings. Bearings wear out periodically so If you hear metal grinding, the bearing(s) may need to be replaced.... [+] | $36.53 |  | | - |
| 31102250CH | Bushing | | $12.66 | | | - |
| 31104840CH1 | CONN ROD ASSY WINSERTS-K22K24K25 | | $109.35 | | | - |
| 31203570CH | Ring | The piston rings provide compression in an air compressor pump by providing the seal in between the cylinder wall and the piston. In an oil-bath... The piston rings provide compression in an air compressor pump by providing the seal in between the cylinder wall and the piston. In an oil-bath pump, there are usually two compression rings and one oil (scraper) ring to keep oil from passing the piston and into the head. In an oil-free pump, the piston is Teflon-coated and doesn’t require lubrication. If your pump is pulling oil into the head or if compression is very low (oil-bath pumps), replace the rings. If your pump isn’t pressurizing or if the piston ring is damaged along the outer perimeter (oil-free pumps), replace it. Also replace the cylinder sleeve when replacing the compression ring (oil-free pumps).... [+] | $18.48 |  | | - |
| 31203580CH | Ring | The piston rings provide compression in an air compressor pump by providing the seal in between the cylinder wall and the piston. In an oil-bath... The piston rings provide compression in an air compressor pump by providing the seal in between the cylinder wall and the piston. In an oil-bath pump, there are usually two compression rings and one oil (scraper) ring to keep oil from passing the piston and into the head. In an oil-free pump, the piston is Teflon-coated and doesn’t require lubrication. If your pump is pulling oil into the head or if compression is very low (oil-bath pumps), replace the rings. If your pump isn’t pressurizing or if the piston ring is damaged along the outer perimeter (oil-free pumps), replace it. Also replace the cylinder sleeve when replacing the compression ring (oil-free pumps).... [+] | $19.31 |  | | - |
| 31203590CH | Ring | The piston rings provide compression in an air compressor pump by providing the seal in between the cylinder wall and the piston. In an oil-bath... The piston rings provide compression in an air compressor pump by providing the seal in between the cylinder wall and the piston. In an oil-bath pump, there are usually two compression rings and one oil (scraper) ring to keep oil from passing the piston and into the head. In an oil-free pump, the piston is Teflon-coated and doesn’t require lubrication. If your pump is pulling oil into the head or if compression is very low (oil-bath pumps), replace the rings. If your pump isn’t pressurizing or if the piston ring is damaged along the outer perimeter (oil-free pumps), replace it. Also replace the cylinder sleeve when replacing the compression ring (oil-free pumps).... [+] | $27.45 |  | | - |
| 31203600CH | Piston, Low-pressure | Low-pressure (larger) piston. Does not include wrist-pin or cap. The piston is an essential component in a compressor pump. Whether it’s an...Low-pressure (larger) piston. Does not include wrist-pin or cap. The piston is an essential component in a compressor pump. Whether it’s an oil-free or oil-bath design, it creates compression on each stroke. In an oil-free design, a Teflon-coated compression ring provides the seal between it and the cylinder sleeve, thereby creating compression; in an oil-bath design, there are compression rings and an oil-ring, like in an internal combustion engine. Replace if the top of the piston is pitted, cracked or warped.... [+] | $99.18 | | | - |
| 31203610CH | Wrist-pin, Low-pressure | Low-pressure wrist pin for piston. | $20.95 | | | - |
| 31204670CH | Wrist-pin, High-pressure | Wrist-Pin for High-Pressure (smaller) piston. | $16.55 | | | - |
| 31204700CH | Compression Ring | (HP) The piston rings provide compression in an air compressor pump by providing the seal in between the cylinder wall and the piston. In an...(HP) The piston rings provide compression in an air compressor pump by providing the seal in between the cylinder wall and the piston. In an oil-bath pump, there are usually two compression rings and one oil (scraper) ring to keep oil from passing the piston and into the head. In an oil-free pump, the piston is Teflon-coated and doesn’t require lubrication. If your pump is pulling oil into the head or if compression is very low (oil-bath pumps), replace the rings. If your pump isn’t pressurizing or if the piston ring is damaged along the outer perimeter (oil-free pumps), replace it. Also replace the cylinder sleeve when replacing the compression ring (oil-free pumps).... [+] | $15.45 |  | | - |
| 31204710CH | Stepped Scraper Ring | (HP) The piston rings provide compression in an air compressor pump by providing the seal in between the cylinder wall and the piston. In an...(HP) The piston rings provide compression in an air compressor pump by providing the seal in between the cylinder wall and the piston. In an oil-bath pump, there are usually two compression rings and one oil (scraper) ring to keep oil from passing the piston and into the head. In an oil-free pump, the piston is Teflon-coated and doesn’t require lubrication. If your pump is pulling oil into the head or if compression is very low (oil-bath pumps), replace the rings. If your pump isn’t pressurizing or if the piston ring is damaged along the outer perimeter (oil-free pumps), replace it. Also replace the cylinder sleeve when replacing the compression ring (oil-free pumps).... [+] | $14.33 |  | | - |
| 31204720CH | Slotted Oil Ring | (HP) The piston rings provide compression in an air compressor pump by providing the seal in between the cylinder wall and the piston. In an...(HP) The piston rings provide compression in an air compressor pump by providing the seal in between the cylinder wall and the piston. In an oil-bath pump, there are usually two compression rings and one oil (scraper) ring to keep oil from passing the piston and into the head. In an oil-free pump, the piston is Teflon-coated and doesn’t require lubrication. If your pump is pulling oil into the head or if compression is very low (oil-bath pumps), replace the rings. If your pump isn’t pressurizing or if the piston ring is damaged along the outer perimeter (oil-free pumps), replace it. Also replace the cylinder sleeve when replacing the compression ring (oil-free pumps).... [+] | $22.04 |  | | - |
| 31206180CH | Piston, High-pressure | High-Pressure (smaller) piston. Does not include wrist-pin or cap. The piston is an essential component in a compressor pump. Whether it’s an...High-Pressure (smaller) piston. Does not include wrist-pin or cap. The piston is an essential component in a compressor pump. Whether it’s an oil-free or oil-bath design, it creates compression on each stroke. In an oil-free design, a Teflon-coated compression ring provides the seal between it and the cylinder sleeve, thereby creating compression; in an oil-bath design, there are compression rings and an oil-ring, like in an internal combustion engine. Replace if the top of the piston is pitted, cracked or warped.... [+] | $115.43 | | | - |
| 31304890CH | Head | Head only. Replace if the head is warped or cracked. Many times a leak occurs because of a hairline fracture. To be sure, spray a soapy water...Head only. Replace if the head is warped or cracked. Many times a leak occurs because of a hairline fracture. To be sure, spray a soapy water solution around the head and if you see bubbles, this is where the leak is. Always replace gaskets when installing a new head, and remove (and sand) the head of any old gasket material.... [+] | $119.23 | | | - |
| 31604730CH | Cylinders | Cylinders for K22, 24 & 25. | $229.50 | | | - |
| 32700350CH | Reed Valve | Qty: 1 valve. Order multiple to complete a set. Poor performance, or does air leak out of the intake air filter while the unit is running? This is...Qty: 1 valve. Order multiple to complete a set. Poor performance, or does air leak out of the intake air filter while the unit is running? This is probably the problem. Damaged/sticking valves is a common issue when you have low compression, and can also cause the motor/engine to stall and too much pressure in the pump’s crankcase. Be sure to clean the head and cylinder very well so as to remove all of the old gasket material and build-up (carbon and rust) when re-installing.... [+] | $5.77 | | | - |
| 32703560CH | Valve LP | Qty: 1 valve. Order multiple to complete a set. Poor performance, or does air leak out of the intake air filter while the unit is running? This is...Qty: 1 valve. Order multiple to complete a set. Poor performance, or does air leak out of the intake air filter while the unit is running? This is probably the problem. Damaged/sticking valves is a common issue when you have low compression, and can also cause the motor/engine to stall and too much pressure in the pump’s crankcase. Be sure to clean the head and cylinder very well so as to remove all of the old gasket material and build-up (carbon and rust) when re-installing.... [+] | $7.53 | | | - |
| 32704750CH | Valve Plate | Poor performance, or does air leak out of the intake air filter while the unit is running? This is probably the problem. Damaged/sticking valves... Poor performance, or does air leak out of the intake air filter while the unit is running? This is probably the problem. Damaged/sticking valves is a common issue when you have low compression, and can also cause the motor/engine to stall and too much pressure in the pump’s crankcase. Be sure to clean the head and cylinder very well so as to remove all of the old gasket material and build-up (carbon and rust) when re-installing.... [+] | $111.38 | | | - |
| 32903710CH | Intercooler, Left | Left intercooler. Does not include o-ring. | $97.14 | | | - |
| 32903720CH | Intercooler, Right | Right intercooler. Does not include o-ring. | $97.14 | | | - |
| 33104600CH | Crankcase | | $180.20 | | | - |
| 36500140CH | GAUGE OIL SIGHT K11 K17 K24 K30 | Oil Site Gauge. Save old gasket. A pressure gauge measures air pressure in the air tank and the pressure to the line from the air regulator. Be...Oil Site Gauge. Save old gasket. A pressure gauge measures air pressure in the air tank and the pressure to the line from the air regulator. Be sure your gauges are accurate; if it is reading the pressure inaccurately it can damage the pump and other components and if the safety valve fails, the tank could explode. Moisture rusts/damages the gauge over time so they must be periodically replaced. Gauges can be air filled or liquid-filled.... [+] | $12.09 |  | | - |
| 36506800CH | Plug | | $13.22 | | | - |
| 36507050CH | BREATHER K50 38_inches | Crankcase breather with o-ring. | $18.21 |  | | - |
| 3690211ACH | Connector | Connector for bottom of intercooler (O-RING STYLE). | $55.97 | | | - |
| 36904930CH | CONNECTOR INTERCOOLER - K24 | | $42.46 | | | - |
| 37300070CH | Bolt | | | | (X) | SOL
No Info |
| 37300250CH | Bolt | | $3.37 | | | - |
| 37301130CH | Screw | | $3.37 | | | - |
| 37301140CH | Bolt | | $3.68 | | | - |
| 37302480CH | SCREW -K24K25K28K30K50K60K100 | | $3.37 | | | - |
| 37302530CH | Bolt | | $3.68 | | | - |
| 37400220CH | Nut | | $2.12 | | | - |
| 37400720CH | Nut | | $4.58 | | | - |
| 37404940CH | NUT K24 K25 | | $2.65 | | | - |
| 37500310CH | Washer | | $2.12 | | | - |
| 37500330CH | Washer | | | | (X) | SOL
No Info |
| 37500400CH | Washer | | $3.37 | | | - |
| 37500670CH | Washer | | | | (X) | SOL
No Info |
| 37500730CH | Washer | | $4.58 | | | - |
| 37602260CH | Ring, Snap | The piston rings provide compression in an air compressor pump by providing the seal in between the cylinder wall and the piston. In an oil-bath... The piston rings provide compression in an air compressor pump by providing the seal in between the cylinder wall and the piston. In an oil-bath pump, there are usually two compression rings and one oil (scraper) ring to keep oil from passing the piston and into the head. In an oil-free pump, the piston is Teflon-coated and doesn’t require lubrication. If your pump is pulling oil into the head or if compression is very low (oil-bath pumps), replace the rings. If your pump isn’t pressurizing or if the piston ring is damaged along the outer perimeter (oil-free pumps), replace it. Also replace the cylinder sleeve when replacing the compression ring (oil-free pumps).... [+] | $4.58 | | | - |
| 431 | ELEMENT FILTER | A clean air filter is essential to the performance of an air compressor. Keep extras on hand as you will inevitably replace it, sometimes often... A clean air filter is essential to the performance of an air compressor. Keep extras on hand as you will inevitably replace it, sometimes often (if used in a contractor or shop application). Some filters have paper elements like automotive air filters, some are simply foam or felt mediums. The filter installs into the inlet side of the pump head and filters out particulates that can damage the pump. Replace every three months or sooner (if used in a shop or jobsite), or whenever you change the oil.... [+] | $10.85 | | | - |
| BLSQPL0250 | Black Plug | | $3.68 | | | - |
| FS14050 | 1/2" MPT Air Filter Assembly | A clean air filter is essential to the performance of an air compressor. Keep extras on hand as you will inevitably replace it, sometimes often... A clean air filter is essential to the performance of an air compressor. Keep extras on hand as you will inevitably replace it, sometimes often (if used in a contractor or shop application). Some filters have paper elements like automotive air filters, some are simply foam or felt mediums. The filter installs into the inlet side of the pump head and filters out particulates that can damage the pump. Replace every three months or sooner (if used in a shop or jobsite), or whenever you change the oil.... [+] | $30.56 |  | | - |
| K24GASKETS | Gasket Set | Gasket kit for K24 pump only. Kit includes every gasket for pump. Gaskets provide a seal between the pump’s components, such as the oil pan,...Gasket kit for K24 pump only. Kit includes every gasket for pump. Gaskets provide a seal between the pump’s components, such as the oil pan, crankcase, cylinder, valve plate(s) and head (as well as the intercooler & aftercooler). Gaskets can be made from metal, cork, silicone, rubber, fiberglass or Teflon. It’s common for gaskets to “blow out” and leak, as debris in the head and back-pressure can damage them. When replacing, clean all old gasket material from the components, and install dry. Tighten the bolts to the correct torque setting for your unit. Having a clean air filter will also minimize gasket damage.... [+] | $45.51 | | | - |
| K24RINGS | Ring Set | Ring set includes all rings necessary, low and high pressure. The piston rings provide compression in an air compressor pump by providing the seal...Ring set includes all rings necessary, low and high pressure. The piston rings provide compression in an air compressor pump by providing the seal in between the cylinder wall and the piston. In an oil-bath pump, there are usually two compression rings and one oil (scraper) ring to keep oil from passing the piston and into the head. In an oil-free pump, the piston is Teflon-coated and doesn’t require lubrication. If your pump is pulling oil into the head or if compression is very low (oil-bath pumps), replace the rings. If your pump isn’t pressurizing or if the piston ring is damaged along the outer perimeter (oil-free pumps), replace it. Also replace the cylinder sleeve when replacing the compression ring (oil-free pumps).... [+] | $81.81 | | | - |
