Belt Guard #058E90

Old Part Numbers: 142-0115Protect your fingers from moving parts. OSHA required.

1/4"Compression Nut & Sleeve #0596D3

(1/4")

Complete Pump with Flywheel #058E46

Old Part Numbers: 040-0352753H Pump Assembly with Flywheel. Ready to bolt on. Just add oil then install your belt and discharge tube.

Belt Guard Bracket #05959A

Old Part Numbers: 114-0391

Flywheel #058E21

12" Flywheel, "A" Groove. Tapered bore is 1.104" to .917".

Connecting Rod Assembly #058E15

One Rod Assy, order qty. 2 if you need to replace both rods. For 755H pump. NOTE: New Conrods do not have Insert Bearings, change in manufacturer of the Conrod. Bearings are machined into the casting of the Rod.

1/2" Compression Nut and Sleeve #05957E

1/2" comp nut & sleeve for 1/2" transfer tube.

Petcock #05959C

Pump Assembly with Flywheel #058DF9

Old Part Numbers: 040-0354, 040-0357755H single-stage, cast-iron pump found on Coleman and Industrial Air units. Includes flywheel and air filter. 13.4 CFM @ 40 psi11.5 CFM @ 90 psi155 psi maximum working pressureSpecifications 1 or 2...

100630502 Breather Small 753H755H #058E0D

Old Part Numbers: 056-0071, 056-0074Thread - 5/8" - 18

Oil Seal #059592

Gasket, Crankcase #05958E

Check Valve #05959E

If your pressure switch is leaking at the unloader valve, replace this part. 1/2" MPT x 1/2" compression.

PULLEY #058E84

3.45"OD x 3/4" bore.

Adapter #058ECC

If your pump has an 'X' in front of the serial number and your supply tube measures 1/2" OD, then order this 1/4" NPT x 1/2" Compression adaptor.

Belt Guard Bracket #058F22

Old Part Numbers: 114-0129use with model EH5593016

Connector #059082

100612012 INLET COVER CAST 753 L71168 #0595EE

Head #058E03

Head for 755H, L710014 Pump. Has TWO outlets (one for the larger supply line and one for the smaller bleeder tube). Two valves are located in the head and two valves located in the valve plate (valve plate not included).

Transfer Tube #058E92

Old Part Numbers: 145-0335Transfer Supply Tube. Order compression nut and sleeve separately.

Gasket, Drv End Cap #059590

Button Plug 7/8 #0590EA

Bearing #058E0F

Ball-bearing for crankcase (205).

V-Belt #058DA1

Old Part Numbers: 007-0048Check to see if yours is 4L540 (54" length).

100605013 CYLINDER 753755H #059AD5

Bleeder Tube #058F9A

Old Part Numbers: 145-0388 Connects between switch and check valve in tank.

Key #05903A

Wheel #0595A0

Order hubcap also if needed.

Key, 5 Mm X 20 Mm #058FE2

Old Part Numbers: 146-00255 mm key to keep flywheel from slipping.

INLET FILTER SCREEN 130 165 #058D63

Old Part Numbers: S118-0032Filter ScreenMetal screen for 130/165 Sanborn style pumps.

Bearing #058E11

Old Part Numbers: 051-0110Ball-bearing for crankcase (206).

SHROUD-PARTIAL BELTGUARD #059598

Old Part Numbers: 142-0114

Gasket, Rear End #05958A

100607317 CRANKCASE 753755H #059ACB

Head & Valveplate Assembly, 755H #058E07

Includes items 1-5, 8, 10, 11 and 12. Has TWO outlet in the head.SpecificationsRPM range 1100-1200

Overhaul Kit #058E09

For 755H pump. This overhaul kit includes items 1-5, 8, 10, 11, 12, 15, 21, 27, 29, 34 and 37.

Cross #0594CF

Brass manifold cross

Valve Plate Assembly #058E0B

Valve plate assembly (includes gaskets). Two valves are located in the head and two valves located in the valve plate (head not included). Poor performance or air leaks out of the intake filter while the unit is running? This is probably the problem.

Ring Set #058E19

Ring set (two required).

Gasket Kit #058E05

Complete gasket kit for pump, including crankshaft seal.

VALVE-RELIEF 170 PSI #059C9A

Pilot Unloader Valve, 125-155 PSI #0595A6

Old Part Numbers: E105379This part is the brains of your air compressor. It controls the engine as well as stops air from going to your air tank when it is full.

Oil Sight Glass #058E1D

Old Part Numbers: 032-0072, 032-0091Oil sight glass w/ O-ring.

Washer, Lock #05916E

Crankshaft #058E1B

Crankshaft for 755H.

(100609505) FILTER FELT 753H PUMP 712201 #05A88B

ELBOW 90D BRASS 269CA4-2 #0596CF

Inline Twin Cylinder 3.7 RHP #0E4250

Gasket, Cylinder #05958C

Head Gasket only. Replace if you remove the head, if leaking, or you have a loss of compression. Recommended to replace the cylinder gasket as well.

Piston Assembly #058E17

Piston assy. (includes wrist pin and retaining rings). Two required.

Overhaul Kit #058E4A

For 753H pump. This overhaul kit includes items 1-5, 8, 10, 11, 12, 15, 21, 27, 29, 34 and 37.

Stabalizer Bar #058E9C

Old Part Numbers: 114-0101Stabalizer Bar for gas units. Diminishes vibration.