NOTE! This Filter will only fit 2HP models! Order part number 90227 for 1HP models. Click here for SKU 90227.Extra DetailsA clean air filter is essential to the performance of an air compress

Old Part Numbers: DY6U2 HP Piston ring for air compressors. This tends to be a high wear part, especially if you are in a high particulate environment. Order the cylinder sleeve when buying this part...

If your unit has a hard time restarting when trying to cycle, order this. If your pressure switch is leaking out of the small bleeder valve on the side (or located underneath), order this valve...

California Air Tools Regulator Manifold for air compressors. The regulator controls the amount of air in your air compressor hose. Replace this if you're not able to adjust the PSI to your hose or if...

1/4" Ball Valve Drain Cock for air compressors. Keep your tank from rusting. Replace this if it is leaking or will not work.

Also known as a "cold start" valve, this integral component releases air off of the piston and pump head after it shuts off, which allows the motor to start much more easily and efficiently. This...

Old Part Numbers: SRV250140Air compressor safety relief valve, 1/4" MPT, 140 PSI. If your valve leaks below the pressure listed on the side of the valve, replace this vital safety feature...

Old Part Numbers: 90393Air compressor pressure switch assembly. If the compressor doesn't cut in or cut out at the designated PSI, most likely the pressure switch is defective. NOTE: If your pressure...

2 HP Piston ring for air compressors. This tends to be a high wear part, especially if you are in a high particulate environment. Order the cylinder sleeve when buying this part as the two wear...

Old Part Numbers: Electromag. Valve 220VFor 220V units.Extra DetailsNOTE! The white plastic thread below may be turned up or down. This is not an error or defect, either one will function perfectly...

California Air Tools Cylinder O-Ring gasket. Note: For newer models with motor serial# ending in "-O".

Electromagnetism Valve for 110V units.

California Air Tools air compressor exhaust hose for 2HP models. Stainless steel braded fluid hose, 3/8" ID.

"T" fitting for the cold start valve. This valve installs into the pump head. The braided discharge tube threads into one end and the cold start valve is installed in the other.

1/4" Quick Connect for California Air Tools air compressors.

2HP Cylinder O-Ring Head Rubber Gasket. Note: For newer models with motor serial# ending in "-OT".

Cylinder o-ring gasket for air compressor pump. Replace if leaking or if you replace the head and/or valve plate.

Gassing Exhaust Valve for air compressors. If you have a loss of compression, replace this exhaust valve and the intake valve.

OEM replacement Pressure Gauge 2.0″ Face, 1/4" NPT Center Back-Mount, 0-180 PSI.

Smaller capacitor for 2 HP, 110V models rated at 90 uF. NOTE! For newer models with unit serial# ending in "-O". Please note: Capacitors can not be returned for a refund unless proven to be defective.

6" White Wheel. Air Compressor Wheel Replacement. NOTE! When ordering the wheel you will also need to order the associated hardware: 90235, Bolt (qty. 1) 91

This is the nylon hose in the intake port of the air intake filter.

Bare Valve Plate for 2 HP motors. Replace if damaged or pitted. Does not include valves.

This is the intake valve that installs on the bottom of the valve plate. Replace if broken or corroded.

NOTE! For newer models with motor serial# ending in "-O".

Larger capacitor for 2 HP, 110V models rated at 150 uF. Please note: Capacitors can not be returned for a refund unless proven to be defective.

The California Air Tools automatic drain valve long extension kit (110V / 60Hz) is designed to eliminate the need to manually drain water and condensate from the air compressor air tank. This kit...