Ring Set for Both Pistons #07F89F

Order rings if your unit is using oil and your valves are good. Hone the cylinder walls prior to installing. Order cylinder gasket if only removing cylinder and installing rings.

GASKET KIT #07F8A5

Includes all necessary gaskets for rebuilding pump.

1/2" MPT Air Filter Assembly #0A12AA

Complete filter assembly including filter element. 1/2" threaded inlet. 2-1/4" x 6-1/4". Takes the #14-SOL Filter Element.

Replacement Filter Element for (#1-4) Filter Assby. #0A12AE

Generic replacement filter element, fits all "FS-14" Assemblies. 4.25"OD x 3"ID x 2 3/8" Height. Replace every 3-4 months if air compressor is used frequently. A dirty filter can cause damage to the pump's valves, clog your check valve and reduce the CFM...

Nut #07FCF4

1/4-14x 1 Hx HD Tek Screw Zp #07FB5D

Old Part Numbers: MFMIS10008

Aftercooler #07F8C7

Old Part Numbers: 305014ACHFinned aftercooler. Order o-ring to go with aftercooler.

GAUGE OIL SIGHT K11 K17 K24 K30 #07F8C1

Old Part Numbers: 30500130CHOil Site Gauge. Save old gasket.

Bolt #07FB47

Ring, Compression Hp #07FCB4

HP Compression ring only.

K17 Pump (Less Flywheel) #07FA2A

Up to 11.11 cfm with 3 HP motor. Cast iron cylinders. Reliable workhorse found on most contractor models. Save money by using your old flywheel and aftercooler. Includes air filter. Footprint is 7.08" x 5.19". Does NOT ship with oil.  Note: A model...

Black Nipple #07FB43

LUBRICATOR 38_inches #07FA26

3/8\" In-line Lubricator.

Bushing #08002E

Item not sold. Requires special machining to use.

Bracket, Accessory #07FB45

THROTTLE CONTROL KIT #07F8DB

Old Part Numbers: MF192EGX160K1QXThrottle control mounts above on/off switch and tells motor when to speed up or slow down. Replace if yours is sticking or leaking.Technical DocumentsClick here for installation instructions

Ring, Scraper #07FCDE

3/8" In-Line Gravity Water Filter #07F8DF

Remove unwanted water from your airlines with this gravity water filter. 3/8" inlet and outlet threads w/ bottom drain valve. Poly bowl. Max inlet pressure 150 PSI.

Support, Flywheel #07FCFC

Pin, Piston #07FCE4

Reed Valve #07FDD8

Qty: 1 valve. Order multiple to complete a set.

Aftercooler Tube Gasket #07F8AB

If leaking occurs around your aftercooler supply line at the head, replace this gasket.

Bolt #07FC92

Aftercooler O-ring #07F8C9

O-ring needed for finned aftercooler.

Seal #07F941

Seal for crank

Black Plug #07FCCC

Cylinder #07FCDA

Brass Nut #07FC89

Gasket #07FDB2

Washer #07FCF2

Piston #07FCE2

Black Nipple #07FB55

Axle #07F9C8

Axle for Semi-pnuematic wheel.

Flywheel #07FC8E

11" diameter with a tapered bore

Cap for Breather #07FCEA

Old Part Numbers: 36531130CHNo longer available, supersedes to part number 36500300CH.

1/4" HD Wingnut Drain Cock #07F8E3

1/4" NPT Heavy Duty drain cock. Prevent rust from ruining your tank by draining your tank daily. Keep an extra around for a spare.

Black Nipple #07FA91

Old Part Numbers: MFBLNP0250X1500

Rolair K17 Pump Rebuild Kit (Rings, Valves, Gaskets, Filter, Oil) #081084

Old Part Numbers: K17REPKIT/10, K17REPKIT/30, K17REPKIT/SYNIncludes most needed parts for a full rebuild. Kit contains: Gasket Set, Oil Sight Glass, Oil Breather/Dipstick, Rings, Air Filter, Reed Valves and Blended Synthetic Compressor Oil (order 2 pair...

Bolt #07FCF0

Oil Drain Tube for GX120-GX200, 10mm #07F8F7

Stop making a mess! This oil drain tube makes changing your oil easy. Simply remove your oil drain plug and install the metric threaded end into your engine block. Changing oil has never been so easy!Technical Documents Click here to an install video...

Valve Plate #07F8C3

If your valve plates are pitted or the valve holes are not lining up with your valves, then you will need to replace these. 2 required for a set. Poor performance or air leaks out of the intake filter while the unit is running? This is probably the...

Washer #07FCD4

Brass Elbow #07FB51

Black Cap #07FB59

Oil Breather Gasket #07F951

3/8" gasket for oil breather.

1/4" NPT drain valve #07FB09

Old Part Numbers: DU25-100Keep your tank from rusting. Replace this if leaking or will not work.SpecificationsBrass, thumb screw.

CRANKCASE BREATHER K50 3/8_INCHES #07F8A9

Old Part Numbers: 36500300CH Crankcase breather with o-ring.

Washer #07FCC2

Tank Assby. #07F8F9

Tank rusted out? Order a new one instead of a whole new compressor. NOTE: Lead time on this tank once ordered is 2 to 3 weeks.

Hose Clamp #07FA22

5/8" Hose Clamp. Uses two.

Foot Rubber #07F8E1

Old Part Numbers: RB1575, 624654Keep your unit from sliding all around your vehicle or floor. Order extra for future use. 3/4" Height, 1 1/2" Diameter

Brass Elbow #07FB57

For COPPER tubing.