Old Part Numbers: E100048, E100104, E100794, E100434, E101178, E100204, E100846Protect your air compressor pump from damage with this air filter assembly intake, 1/2" NPT. Includes the filter base,...

Old Part Numbers: 072-0006Replace this air compressor drain valve if leaking or will not work. Prevent rust from ruining your tank by draining your tank daily. Keep an extra around for a spare. This...

Genuine OEM Flywheel, 12" OD. Includes Mounting Bolt and Washer.Specifications 12" OD Includes Mounting Bolt & Washer Requirements Fits Husky Models: C602H - Type 3 C304H - Type 1  C603H  DeWalt:...

1/2" brass compression and nut and sleeve for rigid tubes. The ferrule/sleeve is built in to the nut.

Old Part Numbers: GA0125200, PG0125200BKAir Compressor Pressure Gauge, 1/8" MPT, Back-Mount, 200 PSI, 1.5" Face. Replace if misreading or broken.Specifications PSI: 0-200 PSI MPT: 1/8" MPT Dial /...

Old Part Numbers: 5130038-00, 5130024-001/4" OD brass compression nut and sleeve for bleeder (unloader) tube for air compressors.

1/2" NPT x 3/8" OD Tube. If your pressure switch is leaking at the unloader valve, replace this part.

Air compressor pump replacement, single-stage, 2 HP, i11. Just bolt on, install your old flywheel, add oil, then install your belt and discharge tube. Note: Does not include flywheel. Order a new...

Old Part Numbers: GA030000AV, A14993, E110954, GA016700AV, GA031000AV, GA015000AVAir Compressor Pressure Gauge. 2" OD Face, 1/4" NPT bottom-mounted thread, 300 PSI gauge. Buy a second one to ensure...

Oil Seal for pump. Replace if oil is leaking from the crankcase around the shaft.

Connecting Rod i11 Service for air compressors. This is the bare connecting rod, no other parts included. Replace if damaged or seized onto the crankshaft.

Old Part Numbers: E105636-MATAdjustable air compressor air pressure regulator assembly (pressure gauge sold separately). If air leaks from the regulator, or when you turn the knob it doesn't adjust...

NOTE: Includes #21 Nut & O-ring Assy!

Replacement Pressure Switch, 135/175 PSI preset pressure, 4-Port manifold (1/4" NPT), Lefoo-style. Replace the pressure switch if the compressor no longer cuts in or cuts out at the designated...

Complete valve plate assembly with head and cylinder o-ring gaskets. If air leaks out of the intake filter or if the compressor just isn't performing like it should, order this kit. A loss of...

1/4" NPT ASME Safety Relief Valve, preset to 200 PSI.  If your valve leaks below the pressure listed on the side of the valve, replace this vital safety feature.

Includes the nut and o-ring seal for the transfer (discharge) tube from the air compressor tank to the pump head.

CAMPBELL HAUSFELD POLY V BELT 460J, 46" FLAT 6 GROOVE OEM PART

Old Part Numbers: E106044, E1106412 HP Regal Beloit electric motor, 115 Volts. 2 HP SPL compressor duty electric motor, ODP (Open Drip Proof) for dry indoor environments Single-Phase, 56 frame, 3,450

#10-14 Plastite screw for the plastic shrouds. Includes 1 screw.

Gasket and o-ring seal kit for the in-line, twin-cylinder i11 air compressor pump includes head o-ring, cylinder o-rings, crankcase gasket, oil sight glass, bearing carrier baffle, and oil seal. If...

Set screws for air compressor motor pulley. Includes 2. Torque to 145 - 180 in/lbs. 

Old Part Numbers: ST084202AV-MATBall bearing, 20mm, 6204.

These are the o-ring seals for the valve plate-to-cylinder.

Includes 2 Piston Assemblies.  Piston (2) Ring Set (2) Pins (2) Retainers (4)

Pipe Nipple, 1/4" NPT-18 x 2.0" length. Make sure to apply Teflon tape to the threads for the proper seal.

Old Part Numbers: D23574Set of 2 bolts, .375-16 X 3.40 UN.

Old Part Numbers: SUDL-431-2, 29.90

3.5" OD X 5/8" Bore Poly-V

Old Part Numbers: E105537, E105991Interconnect cord from the air compressor motor to the pressure switch.

Old Part Numbers: E108246