Old Part Numbers: E100048, E100104, E100794, E100434, E101178, E100204, E100846Protect your air compressor pump from damage with this air filter assembly intake, 1/2" NPT. Includes the filter base,...

Old Part Numbers: 072-0006Replace this air compressor drain valve if leaking or will not work. Prevent rust from ruining your tank by draining your tank daily. Keep an extra around for a spare. This...

Poly-V Pulley, 6.923" outside diameter (OD) with a 5/8" bore (ID). Includes the key and set screws.  

Old Part Numbers: 500J6, BT004800AVAir compressor poly-grooved "J6" belt, 50" circumference. Replace if cracked, worn, or slipping.

Genuine OEM Flywheel, 12" OD. Includes Mounting Bolt and Washer.Specifications 12" OD Includes Mounting Bolt & Washer Requirements Fits Husky Models: C602H - Type 3 C304H - Type 1  C603H  DeWalt:...

1/2" brass compression and nut and sleeve for rigid tubes. The ferrule/sleeve is built in to the nut.

Old Part Numbers: 5130038-00, 5130024-001/4" OD brass compression nut and sleeve for bleeder (unloader) tube for air compressors.

Old Part Numbers: MDR11Condor MDR11 series air compressor pressure switch. Cut-on PSI 120, cut-off PSI 155. 120V / 230V-240V. Replace the pressure switch if the compressor no longer cuts in or cuts...

1/2" NPT x 3/8" OD Tube. If your pressure switch is leaking at the unloader valve, replace this part.

Air compressor pump replacement, single-stage, 2 HP, i11. Just bolt on, install your old flywheel, add oil, then install your belt and discharge tube. Note: Does not include flywheel. Order a new...

Old Part Numbers: SRV250175, 1229O-175Air compressor safety relief valve, 1/4" MPT, 175 PSI, ASME. If your valve leaks below the pressure listed on the side of the valve, replace this vital safety...

Old Part Numbers: GA030000AV, A14993, E110954, GA016700AV, GA031000AV, GA015000AVAir Compressor Pressure Gauge. 2" OD Face, 1/4" NPT bottom-mounted thread, 300 PSI gauge. Buy a second one to ensure...

Oil Seal for pump. Replace if oil is leaking from the crankcase around the shaft.

Connecting Rod i11 Service for air compressors. This is the bare connecting rod, no other parts included. Replace if damaged or seized onto the crankshaft.

NOTE: Includes #21 Nut & O-ring Assy!

Complete valve plate assembly with head and cylinder o-ring gaskets. If air leaks out of the intake filter or if the compressor just isn't performing like it should, order this kit. A loss of...

Includes two O-Rings (2" OD). This is the large O-ring Seal for the inspection port/bushing on the side and bottom (where the drain cock is) of the air tank.

Pressure Relief Tube (no fittings included). This is the 1/4" OD tube that connects from the in-tank check valve to the pump head. 

Includes the nut and o-ring seal for the transfer (discharge) tube from the air compressor tank to the pump head.

Reducer Bushing for the tank, 2" male NPT x 1/4" female NPT. Remember to apply Teflon tape to the threads.

Reducer Bushing for the tank, 2" male NPSM x 3/4" female NPT. Remember to apply Teflon tape to the threads.

#10-14 Plastite screw for the plastic shrouds. Includes 1 screw.

Gasket and o-ring seal kit for the in-line, twin-cylinder i11 air compressor pump includes head o-ring, cylinder o-rings, crankcase gasket, oil sight glass, bearing carrier baffle, and oil seal. If...

Set screws for air compressor motor pulley. Includes 2. Torque to 145 - 180 in/lbs. 

Old Part Numbers: ST084202AV-MATBall bearing, 20mm, 6204.

These are the o-ring seals for the valve plate-to-cylinder.

Includes 2 Piston Assemblies.  Piston (2) Ring Set (2) Pins (2) Retainers (4)

Pipe Nipple, 1/4" NPT-18 x 2.0" length. Make sure to apply Teflon tape to the threads for the proper seal.

Kit of 2

4" x 4" rubber isolator pads.

Old Part Numbers: E105537, E105991Interconnect cord from the air compressor motor to the pressure switch.

Old Part Numbers: E108246