Replacement paper filter element for twist-lock air filter assembly for air compressors. Element only. Replacing the pump's air filter regularly is important to maintain the performance and longevity...

Old Part Numbers: SV25200, SRV250200, 1229O-200, 9710533300, 136-0007RPAir compressor safety relief valve, 1/4" MPT, 200 PSI. If your valve leaks below the pressure listed on the side of the valve,...

Air compressor v-belt, 4L530. Replace if frayed or slipping.Specifications A-type belt, 1/2" wide Outside Dimension: 53" "A" Belt Conversion: A51

Old Part Numbers: FS-10-052Twist-lock air filter assembly for air compressors. 1/2" MPT. Includes 10-SOL filter element. Replacing the pump's air filter regularly is important to maintain the...

Old Part Numbers: L54EReplacement air filter element. 3-3/4" OD x 1-1/4" ID x 2-5/8" High. For A Series units and for filter assemblies with separate cover and wing nut (L54E). Includes the element...

Old Part Numbers: L21K, 310-1001-01Replace this if worn or damaged. Torque to 120 in lbs. (Includes bearing shell inserts). NOTE: These new-style rods will install on old-style (non-bearing insert)...

Old Part Numbers: ESQ, 105-1150Synthetic Blue Air Compressor Oil, 1 Quart. Add oil before use.

Old Part Numbers: 120-1170If your unloader valve leaks or does not unload the pump to start, try replacing this assembly. Located on the end of your air compressor pump with a supply line that runs...

Old Part Numbers: K9Bearing for crankshaft. Order one for each side.

Old Part Numbers: L53BRACKET,FILTER

Old Part Numbers: K36AWrist Pin Retainer (Bumper).

Old Part Numbers: K133This air compressor pump ring kit includes rings for two pistons. Order two sets for v-twin air compressor pumps. Stagger rings and hone cylinders.  Replace if the pump is...

Old Part Numbers: K132Piston Assy w/ piston, ring set, bumpers and wrist pin. Replace this if the rings do not rotate freely in their grooves.

Old Part Numbers: K11EAir compressor oil seal. Oil leaking around the shaft? Remove flywheel and replace this seal. Need oil? 

Replacement bearing shells for connecting rod. (order 2 for each connecting rod) Works with old style (non-bearing) and new style.

Old Part Numbers: KU86 1/4" compression x 1/8" male NPT air compressor compression elbow. Note: For COPPER tubing. If you are using nylon or plastic tubing, consider using our T1059.

Old Part Numbers: 610-1125, DU101, GU101Complete rebuild kit for entire air compressor pump. Includes the piston rings, gaskets, intake and exhaust valves, unloader valves, and canister-style air...

Old Part Numbers: 68-4-21/8" male NPT x 1/4" compression adapter for air compressor unloader/bleeder line. A very common adapter to attach the 1/4" OD unloader/bleeder line from the unloader valve on...

Old Part Numbers: L100All the gaskets necessary to rebuild your D, DC, DCU, G, GU, GCU, L, LC, LU, LCU, MG or MGU Pump. (Incl. L3, L4,2-K31,2-L41,2-L51)

Old Part Numbers: 220-1032, EQ23, GT23A13.25" OD, 7/8" ID, 2-groove flywheel for model "DC" pump, includes K25 roll pin.

Old Part Numbers: K32 Piston and bumpers (no rings).

Old Part Numbers: G54EPPackage of four (4) G54E hockey puck-style filter elements. Element only for air compressor air filter assembly. Replacing the pump's air filter regularly is important to...

Old Part Numbers: EQ100Includes all gaskets for the Emglo / Jenny GT / GTU air compressor pumps: head gaskets (HP & LP sides), valve plate-to-cylinder gaskets, crankcase gaskets, and bearing cover...

Old Part Numbers: PG3Replace if misreading or broken.

Old Part Numbers: K25For flywheel. Replace when rebuilding pump. Included in the KU Rebuild Kit.

Old Part Numbers: 610-1128Complete rebuild kit for the Emglo/Jenny EQ, GT, and Y air compressor pumps. Rebuild Kit includes piston rings, gaskets, intake and exhaust valves, L54E hollow-style air...

Old Part Numbers: G101, 610-1124Rebuild Kit for the Emglo/Jenny G, GC, MG, L, LC, D air compressor pumps. Includes piston rings, gaskets, intake and exhaust valves, and G54E hockey puck-style air...

Complete, new GT pump with flywheel and air filters. Two-stage, v-twin pump with cast-iron construction. See Specs for CFM output. This pump replaces the EQ pump. New pump w/ flywheel & air filter...

Old Part Numbers: L54EThis handy maintenance kit includes one air compressor air filter element and one (1) quart of high-quality full synthetic lubricant to keep your air compressor running like a...

Old Part Numbers: K35Wrist Pin (Piston Pin) for conrod.

Old Part Numbers: L154Newer wingnut-style filter assy with L54E hollow-style element. Uses filter 150-1010-JE filter element. Replacing the pump's air filter regularly is important to maintain the...

Old Part Numbers: L9If loose or dirty, replace these when rebuilding pump.

Old Part Numbers: 320-1014, 320-1179Protect your fingers from moving parts. OSHA required. 3.38" wide x 14.63" high x 28" long.

Everything you need for a valve job. Includes, intake, exhaust valves. Even includes necessary gaskets. Torque head bolts to 250 in/lbs.

Old Part Numbers: PB2HP, 145-175 PSI; If your valve is leaking on the side of the switch do not order this part. Order check valve instead. 

Old Part Numbers: L18

Old Part Numbers: MC-5SNote: order this item for model GT5B-120.

1/8" MPT x 1/4" compression T

Old Part Numbers: LU88Unloader  Tube w/ Fittings

Old Part Numbers: EQ65Finned intercooler tube w/ flare nuts. (furthest from flywheel)

Old Part Numbers: ESG1 Gallon of premium Jenny Ultimate Blue Synthetic Air Compressor Pump Oil. Formulated specifically for air compressor pumps. ISO 100. This synthetic compressor oil is 20-weight...

Old Part Numbers: SVU651/4 in, 65 PSI Safety Valve.

Old Part Numbers: K52-1

Old Part Numbers: Y20AOEM Crankshaft. If yours is pitted or grooved, replace it. Use new connecting rods.

Old Part Numbers: EQ62Finned intercooler tube w/ flare nuts. (closest to flywheel)

Old Part Numbers: K30Cylinder for K series and D/DC/DCU air compressor pumps.

Old Part Numbers: EQ132High Pressure (HP) Piston with wrist pin and rings.

Old Part Numbers: K32WThis is the hi pressure piston. The other 3 are lo pressure pistons.

Old Part Numbers: G154PIncludes four G154 complete filter assemblies. This air compressor air filter assembly is the older twist-lock filter with hockey-puck filter elements. Replacing the pump's air...

NOTE: For units made BEFORE 2003. If your pressure switch is leaking at the unloader valve, replace this part.

Old Part Numbers: L55Wingnut for old style air filter.

2 HP, 230-460 Volts, 50-60 Hz/3-Phase, 1,725 RPM.

SCREW,CAP,HEX HD,GR5,ST,BLK

2 FT

Old Part Numbers: EQ38For High Pressure piston.

Old Part Numbers: L21WThis is the one with the EQ38 bronze bushing insert. You need 3 L21L connecting rods and one of these to replace all 4 connecting rods. Order wrist & roll pin also if needed...

Old Part Numbers: 122-1042-JE Jenny Pipe Nipple (122-1144)

Old Part Numbers: EQ35High Pressure wrist pin.

Old Part Numbers: EQ37Roll Pin for High Pressure piston.

Old Part Numbers: EQ71

Old Part Numbers: GV12 Quick and easy 1/4 turn cuts it on or off. Industrial Quality. 1/2" FPT on each end.

Old Part Numbers: W40, 220-1041PLATE,VALVE,W PUMP,CI,MACHINED

Old Part Numbers: L54EThis handy maintenance kit includes one air compressor air filter element and one (1) quart of high-quality synthetic blend lubricant to keep your air compressor running like a...

Old Part Numbers: 610-1129, EQU101, GTU101Rebuild Kit Incl. Rings, Gaskets, Valves, Unloader Valves and Air Filter Elements (L54E hollow style).

Old Part Numbers: K14Crankcase bolt (oil fill), K series

Everything you need for a valve job. Includes, intake, exhaust and unloader valves. Even includes necessary gaskets. Torque head bolts to 250 in/lbs.

See Specs for CFM output. This pump replaces the EQU pump. New pump w/ flywheel & air filter assemblies. Has head unloaders for constant run units (gas). Has two-groove Flywheel. Need oil? 

LOCK,FLANGE,HEX,SERR,ST,PLTD,5/16-18

Old Part Numbers: EQ73B

Old Part Numbers: EQ73

Old Part Numbers: EQ72

Old Part Numbers: EQ70

Old Part Numbers: 3412If your pressure switch is leaking at the unloader valve, replace this part. 

2 HP, 200-208 Volts, 60 Hz/1-Phase, 1,725 RPM.

2 HP, 200-208 Volts, 60 Hz/3-Phase, 1,725 RPM.

Everything you need for a valve job for this high pressure breaker pump. Includes,stainless intake, stainless exhaust and unloader valves. Even includes necessary gaskets. Torque head bolts to 250...

Old Part Numbers: EQ50Right Head for start-stop units.

Old Part Numbers: K15O-ring for oil fill bolt

Old Part Numbers: EQ180 Right Head for constant run units (includes unloaders).  Sale item - 2 in stock (no retuns)  For Emglo pumps: Emglo GT, GTU, W, Y, and other model Emglo pumps. 

Old Part Numbers: L22

Old Part Numbers: EQ170Weight Assy. for Cent. Unloader.

Old Part Numbers: Y175Complete Centrifugal Unloader Assy. for Y and YU pumps.