NOTE! This Filter will only fit 2HP models! Order part number 90227 for 1HP models. Click here for SKU 90227.Extra DetailsA clean air filter is essential to the performance of an air compress

Old Part Numbers: DY6U2 HP Piston ring for air compressors. This tends to be a high wear part, especially if you are in a high particulate environment. Order the cylinder sleeve when buying this part...

If your unit has a hard time restarting when trying to cycle, order this. If your pressure switch is leaking out of the small bleeder valve on the side (or located underneath), order this valve...

1/4" Ball Valve Drain Cock for air compressors. Keep your tank from rusting. Replace this if it is leaking or will not work.

Also known as a "cold start" valve, this integral component releases air off of the piston and pump head after it shuts off, which allows the motor to start much more easily and efficiently. This...

Old Part Numbers: SRV250140Air compressor safety relief valve, 1/4" MPT, 140 PSI. If your valve leaks below the pressure listed on the side of the valve, replace this vital safety feature...

Old Part Numbers: 90393Air compressor pressure switch assembly. If the compressor doesn't cut in or cut out at the designated PSI, most likely the pressure switch is defective. NOTE: If your pressure...

2 HP Piston ring for air compressors. This tends to be a high wear part, especially if you are in a high particulate environment. Order the cylinder sleeve when buying this part as the two wear...

Old Part Numbers: Electromag. Valve 220VFor 220V units.Extra DetailsNOTE! The white plastic thread below may be turned up or down. This is not an error or defect, either one will function perfectly...

California Air Tools Cylinder O-Ring gasket. Note: For newer models with motor serial# ending in "-O".

California Air Tools air compressor exhaust hose for 2HP models. Stainless steel braded fluid hose, 3/8" ID.

"T" fitting for the cold start valve. This valve installs into the pump head. The braided discharge tube threads into one end and the cold start valve is installed in the other.

2HP Cylinder O-Ring Head Rubber Gasket. Note: For newer models with motor serial# ending in "-OT".

California Air Tools MP2012 cylinder for air compressor repairs.  Replace the cylinder if it is damaged or worn, or if you are also replacing the compression ring.

Old Part Numbers: MP218-O, MP2018-OThis is the o-ring seal for each end of the pump connecting hoses, which connects the two air compressor pump heads.

Gassing Exhaust Valve for air compressors. If you have a loss of compression, replace this exhaust valve and the intake valve.

California Air Tools MP2012-O cylinder for air compressor repairs.  Replace the cylinder if it is damaged or worn, or if you are also replacing the compression ring. NOTE: For newer models with motor...

OEM replacement Pressure Gauge 2.0″ Face, 1/4" NPT Center Back-Mount, 0-180 PSI.

Smaller capacitor for 2 HP, 110V models rated at 90 uF. NOTE! For newer models with unit serial# ending in "-O". Please note: Capacitors can not be returned for a refund unless proven to be defective.

This is the nylon hose in the intake port of the air intake filter.

Washer for the Cushion Foot.

Bolt for Cushion Foot.

Rubber Foot Cushion for the compressor base. Keep your compressor from damage caused by vibration and from walking around, and replace the feet if missing or damaged.

California Air Tools Air Compressor Pump Replacement, Complete Assembly, Ultra Quiet, Oil-Free, 2 HP. Comes with: (1) capacitor, (2) air filters, and (4) shock struts. Oil-Free Pump = Cleaner air for...

NOTE! For newer models with motor serial# ending in "-O".  2 HP Pressure Plate

This is the intake valve that installs on the bottom of the valve plate. Replace if broken or corroded.

Bare Pump Head. Both cylinders use the same pump head. NOTE: Does not include any gaskets/seals, order separately.

Steel Plug for the pump head.

California Air Tools air compressor nut for cushion foot.

2HP Shock Strut

Bare Valve Plate for California Air Tools 1 HP pumps. Replaced if damaged or warped.

Cylinder Cup for 1 HP pumps. Replace when replacing the Piston (Compression) Ring.

Old Part Numbers: Left Fan-CAT

SR-7K-2 Black Strain Relief

Power Cord with Plug for California Air Tools air compressors, 110V.

Old Part Numbers: SYQ67U-10020

Larger capacitor for 2 HP, 110V models rated at 150 uF. Please note: Capacitors can not be returned for a refund unless proven to be defective.

Screw that holds on the fan cover to the pump. 2HP Fan Cover Screw

2HP Adjustment Stent