1/2" MPT Air Filter Assembly #0A12A2

Old Part Numbers: G154S1/2" MPT x Ht 4.19" x W 4.12" Twist lock Uses 10 element.

1/2" MPT Air Filter Assembly #0A12A0

Metal Assy, 1/2" MPT x Ht 3.80" x W 3.25" Twist Lock. Uses 06 element.

COMPRESSION ADAPTER #0E52EE

Old Part Numbers: 68-6-4If your pump has an 'X' in front of the serial number and your supply tube measures 3/8" OD, then order this 1/4" NPT x 3/8" Compression adaptor.

Oil Pan Gasket #058D7B

If replacing crank or rings, replace this gasket. (8 bolt style)

Belt Guard #058E90

Old Part Numbers: 142-0115Protect your fingers from moving parts. OSHA required.

FLYWHEEL WASHER 755H PUMP (100631601) #05A7D9

Dipstick #0592D6

1/4"Compression Nut & Sleeve #0596D3

(1/4")

Pump with flywheel and filter assby #0E4254

Connecting Rod Up to 4.5hp #058D4B

Connecting Rod up to 4.5HP for 130 pump. Torque 160-200 in. lbs.

Oil Seal #058E60

Replace when removing crankshaft, bearings or if leaking.

Belt Guard Bracket #05959A

Old Part Numbers: 114-0391

Flywheel #058E21

12" Flywheel, "A" Groove. Tapered bore is 1.104" to .917".

Cylinder Gasket #0592D8

Available in the 130/165VPGASKETS kit only.

Piston #058D53

Piston for 130 & 165 pump. Includes wrist pin and two retainers.

1/2" Compression Nut and Sleeve #05957E

1/2" comp nut & sleeve for 1/2" transfer tube.

Petcock #05959C

Check Valve #05959E

If your pressure switch is leaking at the unloader valve, replace this part. 1/2" MPT x 1/2" compression.

PULLEY #058E84

3.45"OD x 3/4" bore.

Adapter #058ECC

If your pump has an 'X' in front of the serial number and your supply tube measures 1/2" OD, then order this 1/4" NPT x 1/2" Compression adaptor.

Connecting Rod for 5 Hp And Up. #058D4D

Connecting Rod for 5 HP and greater for 165 pump. Torque 160-200 in. lbs.

Air Filter Element #058D5B

#8 hollow filter for older Sanborn pumps (old wing nut style)(ea.) 2.25" Width & 2.25" Height Protect your pump from damage by keeping clean or replacing.

Belt Guard Bracket #058F22

Old Part Numbers: 114-0129use with model EH5593016

Connector #059082

165 Pump With Flywheel & Air Filter #0E4256

For 5 to 6.5 HP units. Complete, new 165 Pump with felt Air Filter and Flywheel. Don't forget the air compressor oil! Older models had a "B"-groove flywheel to accept 5/8" wide belts. The new flywheel has an "A"-groove flywheel that accepts 1/2"...

Hubcap, 1/2" #058E31

Hubcap for wheel, 1/2". Two required.

Piston Rings #058D55

Includes rings for both pistons for the 130/165 pump.

Bearing #058EC8

Roller bearing. (Older pumps had obsolete bronze bushing, order new pump if damaged)

Pilot/unloader Valve #058E96

Pilot/Unloader Valve, 100 - 130 psi. Replace if compressor will not cut in or cut out at designated pressure.

Button Plug 7/8 #0590EA

Head Kit #058EC2

This kit includes: New head as well as compression adaptors for 3/8" or 1/2" supply tubes. (Order head gaskets if needed)

Handle #058E27

Old Part Numbers: 112-0031Replacement handle for part # 112-0031.

Gasket #0592CE

Key, 5 Mm X 20 Mm #058FE2

Old Part Numbers: 146-00255 mm key to keep flywheel from slipping.

Gasket Kit for 130/165 Pumps #058D81

Includes gaskets for rebuild. Includes SKUs: 046-0149, 046-0150, 046-0151, 046-0152, 046-0263.

INLET FILTER SCREEN 130 165 #058D63

Old Part Numbers: S118-0032Filter ScreenMetal screen for 130/165 Sanborn style pumps.

Pressure Gauge, 300 PSI 1/8" Backmount, 1.70" Diameter #058D9D

Old Part Numbers: 032-0056, 032-0001Pressure gauge.

AIR FILTER (WOOLFLT) 130 165 #058D47

Felt filter for Sanborn 130/165 style pumps. Approximately 1 1/4" x 4 1/2" x 3/8" thick. Order 2 or 3 for spares. Replace this every 3-4 months if the compressor is used frequently. A clean filter allows your pump to operate at its max efficiency!

SHROUD-PARTIAL BELTGUARD #059598

Old Part Numbers: 142-0114

Crankshaft for 165 Pump (5 Hp) #058D51

Replace this also if your crank is grooved or pitted. Make sure you have the correct pump. There is a 130 and 165 pump. They both look the same on the outside.

O-Ring 1 1/2" #0590E6

Cross #0594CF

Brass manifold cross

Wheel, 9" #058E3B

Old Part Numbers: 095-0028, 095-0045, 095-0080 Wheel for unit. 9" diameter, 1/2" bore. Replaces 095-0028, 095-0045.

Foot #058E6C

Rubber isolator foot. Reduces vibration and noise.

Overhaul Kit (Felt Filter) #058D43

Old Part Numbers: 165-0055Overhaul kit for pump. Includes new style valve plate, gaskets, rings, and felt air filter. 

SCREW M8 X 25MM (201010074) #05A7EB

130 Pump (No Flywheel) #058FA2

Old Part Numbers: 040-0196Used on units up to 4.5 HP motors. Pump includes felt filter. Flywheel is not included. NOTE! If ordering a new 130 Pump, you can use the Head from your original pump, as it will retrofit onto the new Pump. This is necessary for...

ELBOW 90D BRASS 269CA4-2 #0596CF

VALVE PRESS RLF 145 PSI #059C94

Head Gasket #058D49

Only available in 130/165VPGASKETS gasket kit. Search for SKU#: 130/165VPGASKETS on our site to order.

Bearing Carrier with Bearing #058FE4

Old Part Numbers: 045-0043Bearing carrier and bearing for flywheel end..

Oil Pan (14 Hole) #058EB8

Replace if cracked. Order gasket also.