1/2" MPT Air Filter Assembly #0A12A0

Metal Assy, 1/2" MPT x Ht 3.80" x W 3.25" Twist Lock. Uses 06 element.

COMPRESSION ADAPTER #0E52EE

Old Part Numbers: 68-6-4If your pump has an 'X' in front of the serial number and your supply tube measures 3/8" OD, then order this 1/4" NPT x 3/8" Compression adaptor.

1/8" Wingnut Drain Cock, #07F8FB

Old Part Numbers: DC141/8" NPT drain cock. Prevent rust from ruining your tank by draining your tank daily. Keep an extra around for a spare.

Air Regulator, 1/4" Mini #07F896

Old Part Numbers: 150-1143, 641133Universal Regulator: 4-port, two 1/4" FPT ports and two 1/8" FPT ports (gauges sold separately). The Regulator controls the amount of air to your hose. Replace this if you're not able to adjust the PSI to your hose or if...

Relief Valve, PS2020 #07F901

This is located on the side of the pressure switch. If your valve is attached to your switch by inserting through a hole on the side bracket, then this is your style. Order this if your valve is broken. If this valve leaks continuously after it shuts...

Oil Pan Gasket #058D7B

If replacing crank or rings, replace this gasket. (8 bolt style)

FLYWHEEL WASHER 755H PUMP (100631601) #05A7D9

Dipstick #0592D6

Pump with flywheel and filter assby #0E4254

Connecting Rod Up to 4.5hp #058D4B

Connecting Rod up to 4.5HP for 130 pump. Torque 160-200 in. lbs.

Oil Seal #058E60

Replace when removing crankshaft, bearings or if leaking.

Flywheel #058E21

12" Flywheel, "A" Groove. Tapered bore is 1.104" to .917".

Cylinder Gasket #0592D8

Available in the 130/165VPGASKETS kit only.

Piston #058D53

Piston for 130 & 165 pump. Includes wrist pin and two retainers.

Conn-male #059256

Blt Grd Brkt #059254

Old Part Numbers: 114-0006use with model CT5590816, CT5590816.01, CT5090810, HT5590816

Adapter #058ECC

If your pump has an 'X' in front of the serial number and your supply tube measures 1/2" OD, then order this 1/4" NPT x 1/2" Compression adaptor.

Connecting Rod for 5 Hp And Up. #058D4D

Connecting Rod for 5 HP and greater for 165 pump. Torque 160-200 in. lbs.

Air Filter Element #058D5B

#8 hollow filter for older Sanborn pumps (old wing nut style)(ea.) 2.25" Width & 2.25" Height Protect your pump from damage by keeping clean or replacing.

Belt Guard Bracket #058F22

Old Part Numbers: 114-0129use with model EH5593016

Connector #059082

165 Pump With Flywheel & Air Filter #0E4256

For 5 to 6.5 HP units. Complete, new 165 Pump with felt Air Filter and Flywheel. Don't forget the air compressor oil! Older models had a "B"-groove flywheel to accept 5/8" wide belts. The new flywheel has an "A"-groove flywheel that accepts 1/2"...

Piston Rings #058D55

Includes rings for both pistons for the 130/165 pump.

Bearing #058EC8

Roller bearing. (Older pumps had obsolete bronze bushing, order new pump if damaged)

Head Kit #058EC2

This kit includes: New head as well as compression adaptors for 3/8" or 1/2" supply tubes. (Order head gaskets if needed)

Key #05903A

Handle #058E27

Old Part Numbers: 112-0031Replacement handle for part # 112-0031.

Gasket #0592CE

Key, 5 Mm X 20 Mm #058FE2

Old Part Numbers: 146-00255 mm key to keep flywheel from slipping.

Gasket Kit for 130/165 Pumps #058D81

Includes 6,16,21a,21b gaskets for rebuild. Includes both style oil pan gaskets.

INLET FILTER SCREEN 130 165 #058D63

Old Part Numbers: S118-0032Filter ScreenMetal screen for 130/165 Sanborn style pumps.

AIR FILTER (WOOLFLT) 130 165 #058D47

Felt filter for Sanborn 130/165 style pumps. Approximately 1 1/4" x 4 1/2" x 3/8" thick. Order 2 or 3 for spares. Replace this every 3-4 months if the compressor is used frequently. A clean filter allows your pump to operate at its max efficiency!

Crankshaft for 165 Pump (5 Hp) #058D51

Replace this also if your crank is grooved or pitted. Make sure you have the correct pump. There is a 130 and 165 pump. They both look the same on the outside.

Shroud #0590F2

TUBE-TRANSFER 1/2" #058DA3

Order if cracked or bent. Order 058-0016 nut/sleeve also.

Regulator Valve #0594CD

Old Part Numbers: 019-0114OEM Adjustable Regulator assembly for units that have a 4 port pressure switch. (Gauge sold separately). 3 Port Regulator

Overhaul Kit (Felt Filter) #058D43

Old Part Numbers: 165-0055Overhaul kit for pump. Includes new style valve plate, gaskets, rings and felt air filter. Click 'Specs' before ordering parts.

SCREW M8 X 25MM (201010074) #05A7EB

130 Pump (No Flywheel) #058FA2

Old Part Numbers: 040-0196Used on units up to 4.5 HP motors. Pump includes felt filter. Flywheel is not included. NOTE! If ordering a new 130 Pump, you can use the Head from your original pump, as it will retrofit onto the new Pump. This is necessary for...

Head Gasket #058D49

Available in the 130/165VPGASKETS kit only.

Bearing Carrier with Bearing #058FE4

Old Part Numbers: 045-0043Bearing carrier and bearing for flywheel end..

Oil Pan (14 Hole) #058EB8

Replace if cracked. Order gasket also.

Bearing #058E64

Flywheel end bearing.

165 Pump w/out Flywheel #058D69

Old Part Numbers: 040-0311 For 5 to 6.5 HP units. New Pump with felt air filter to replace original pump. Flywheel NOT included. Simply swap out flywheel, add oil and run.  NOTE! New style pump has 1/4" FPT & 1/8" FPT outlet ports in head (Your...

CRANKCASE ASSY 130165 #058EBC

For 14 bolt pattern.

Oil Pan Gasket #058D79

If replacing crank or rings, replace this gasket. (14 bolt style)

Valve Plate Kit #058D45

Click 'Specs' regarding this part first. Poor performance or air leaks out of the intake filter while the unit is running? This is probably the problem. Click here to view installation instructionsTechnical DocumentsClick here for Valve Plate...

Valve Plate Gaskets #05C0B9

Includes (1) 046-0151 Head Gasket and (1) 046-0152 Cylinder Gasket.

Valve Plate Assy with Filters #05C100

Restore compression and keep your new Valves in good shape with this convenient kit! Poor performance or does air leak out of the intake filter while the unit is running? This is probably the problem. Includes Valve Plate Assy with both Gaskets and two...

090-120 PSI Furnas Hubbell Pressure Switch #048A8B

Old Part Numbers: 034-0097OEM Switch. 1 port; 90-120 PSI, unloader and on/off lever. If your valve is leaking on the side of the switch do not order this part. Order check valve instead. Specifications

CTD1212 Check Valve #022ADE

Old Part Numbers: CV4X4T1/2" Comp X 1/2" MPT with 1/8" FPT side port.Video