Old Part Numbers: 019-0246, 019-0023Replacement air filter element, Rolair 431. Fits the K12 through K30 air compressor pumps.

Old Part Numbers: TF060402AVCampbell Hausfeld Tube Fitting with Compression Nut (175 PSI) for air compressors. Head Fitting including screws, compression nut, compression sleeve and o-rings.

Old Part Numbers: SV25200, SRV250200, 1229O-200, 9710533300, 136-0007RPAir compressor safety relief valve, 1/4" MPT, 200 PSI. If your valve leaks below the pressure listed on the side of the valve,...

Old Part Numbers: TF059700AJ, TF061700AJBroken valve causing slow pressurization or no compression at all? Replace this head and valve plate assembly to restore compression. Includes everything...

Old Part Numbers: TF002000BHIntercooler Tube that connects from one cylinder to the other. Replace if kinked or punctured. Note: Does not include fittings.

Polyester air filter element for air compressors. Found on many larger units and older units. Fits the S1097 & 1312100375 filter assemblies. .5 micron up to 6,600 SCFM

Tube Fitting Assembly includes fitting, compression nut & ferrule, screws, 1/8" MPT plug and o-ring. Note: Order this item for model 5Z404E and others.

Air intake filter kit includes the canister assembly, filter element, o-ring seal, bolts, nuts, and washers. Replacing the pump's air filter regularly is important to maintain the performance and...

Campbell Hausfeld Air Compressor Pump Gasket Kit includes all main gaskets and o-rings seals. Important: For v-twin pumps, you'll need to order 2 kits to rebuild the complete pump. Note: Inlet gasket...

This is the 3/4" Ferrule (Sleeve) for the triangular Tube Fittings to the Pump Head.

Note: order this item for model 5Z404E.

Stagger rings and hone cylinders when installing. Includes piston rings for two air compressor pistons. NOTE: For v-twin pumps, you need qty. 2 to rebuild complete pump.Technical DocumentsClick here...

Old Part Numbers: HS003900AVOil Breather Assembly with Extension Tube and Mesh Filter. 

This is the Gasket in between the pump's crankcase and the cylinder. Also included in a complete Gasket Kit.

Old Part Numbers: CI050000PC, CI070000PD, TF2111, TF2511, CI050000PD, TF2101, TF2501OEM twin-cylinder, two-stage replacement air compressor pump with flywheel, intercoolers, and air filter assembly...

Old Part Numbers: 3168Air compressor pressure switch/manifold pipe plug, 1/4"-18 male NPT. A very common hex plug used on countless air compressors, this 1/4" NPT countersunk hex plug installs into...

Old Part Numbers: cCrankcase Breather Assembly with O-rings. This part allows the crankcase to vent to prevent too much pressure from building up in the crankcase.

3/8" male NPT Drain Cock for the tank. Prevent rust from ruining your tank by draining your tank daily. Keep an extra around for a spare!

Old Part Numbers: TF061300AVCylinder-to-Valve Plate Gasket. Remember to tighten the head bolts down to the appropriate torque spec when reinstalling the head.

Old Part Numbers: 61-12, 997-57781Compression nut, 3/4" OD, brass. Don't forget the compression sleeve/ferrule! 

Old Part Numbers: TF060300AVHead Gasket for the TF/TX series pumps. Replace if leaking or if the intercooler safety relief valve blows off.

16.5" CI Pump Flywheel, 1-Belt with Key for air compressors. Taper Bore - 1.32 to 1.51. Has now been changed to a single-groove flywheel. Will still work with two-groove motor pulley.

Old Part Numbers: CV006411SJThrottle control cable is 33.25".

Air compressor pump air filter kit includes the canister assembly, filter element, bolts, washers, and wingnut. Note: Order this kit for CI0500 models and others. Replacing the pump's air filter...

Connecting rod assembly. Includes the needle bearing, insert bearings, bolts, and dipper. Used on many CI0500, CI0700, TF2001, TF2101, TF2111, and TF2912 air compressor pumps.

Old Part Numbers: ST074415AV, ST120200AV, ST073236AVIncludes six (6) screws.

Needle bearing for connecting rod (one used per rod).

Old Part Numbers: TF050100AV

Tube only (no fittings).

Smaller, high-pressure (HP) piston with rings. Stagger rings and hone cylinder prior to installing.

Larger, Low-Pressure (LP) Piston with rings. Stagger the rings and hone cylinder prior to installing.

Campbell Hausfeld load genie check valve.  This valve is a combo check valve and pilot unloader valve.  This valve is used on units that are continously running air compressors (many Campbell...

Old Part Numbers: ST016500AV

New crankshaft assembly with ball bearings.

Old Part Numbers: ST000600AV(1/4)

Old Part Numbers: TF202700AV

BT010800AV Campbell Hausfeld Air Compressor V Belt. 80-inch replacement drve belt. BX-77.

Bare Cylinder for two-stage pump. Order any necessary gaskets separately.

Old Part Numbers: ST072025AV

Old Part Numbers: GA016703AVReplacement Pressure Gauge, 300 psi, 2" Face, Back-Mount (1/4" male NPT).