Old Part Numbers: 019-0246, 019-0023Replacement air filter element, Rolair 431. Fits the K12 through K30 air compressor pumps.

Old Part Numbers: TF060402AVCampbell Hausfeld Tube Fitting with Compression Nut (175 PSI) for air compressors. Head Fitting including screws, compression nut, compression sleeve and o-rings.

Old Part Numbers: SV25200, SRV250200, 1229O-200, 9710533300, 136-0007RPAir compressor safety relief valve, 1/4" MPT, 200 PSI. If your valve leaks below the pressure listed on the side of the valve,...

Old Part Numbers: TF059700AJ, TF061700AJBroken valve causing slow pressurization or no compression at all? Replace this head and valve plate assembly to restore compression. Includes everything...

Old Part Numbers: TF002000BHIntercooler Tube that connects from one cylinder to the other. Replace if kinked or punctured. Note: Does not include fittings.

O-Ring Seal for the triangular intercooler and aftercooler fittings on the pump head.

Polyester air filter element for air compressors. Found on many larger units and older units. Fits the S1097 & 1312100375 filter assemblies. .5 micron up to 6,600 SCFM

Tube Fitting Assembly includes fitting, compression nut & ferrule, screws, 1/8" MPT plug and o-ring. Note: Order this item for model 5Z404E and others.

Air intake filter kit includes the canister assembly, filter element, o-ring seal, bolts, nuts, and washers. Replacing the pump's air filter regularly is important to maintain the performance and...

Campbell Hausfeld Air Compressor Pump Gasket Kit includes all main gaskets and o-rings seals. Important: For v-twin pumps, you'll need to order 2 kits to rebuild the complete pump. Note: Inlet gasket...

Old Part Numbers: ST072321AV, 058-00123/4" compression nut & sleeve (2 required). For air compressor units made before 05/20/1994.

This is the 3/4" Ferrule (Sleeve) for the triangular Tube Fittings to the Pump Head.

Old Part Numbers: HS003900AVOil Breather Assembly with Extension Tube and Mesh Filter. 

Note: order this item for model 5Z404E.

Stagger rings and hone cylinders when installing. Includes piston rings for two air compressor pistons. NOTE: For v-twin pumps, you need qty. 2 to rebuild complete pump.Technical DocumentsClick here...

Old Part Numbers: CI050000PC, CI070000PD, TF2111, TF2511, CI050000PD, TF2101, TF2501OEM twin-cylinder, two-stage replacement air compressor pump with flywheel, intercoolers, and air filter assembly...

This is the Gasket in between the pump's crankcase and the cylinder. Also included in a complete Gasket Kit.

Old Part Numbers: PU011105AV, PU011100AV16" OD 2-belt cast iron flywheel with key. Note: For CI10 models. This flywheel is tapered. It is 1.32", taper rate is .06 per inch. Tapered Bore 1 3/16" - 1...

Old Part Numbers: 3168Air compressor pressure switch/manifold pipe plug, 1/4"-18 male NPT. A very common hex plug used on countless air compressors, this 1/4" NPT countersunk hex plug installs into...

Old Part Numbers: cCrankcase Breather Assembly with O-rings. This part allows the crankcase to vent to prevent too much pressure from building up in the crankcase.

Old Part Numbers: 61-12, 997-57781Compression nut, 3/4" OD, brass. Don't forget the compression sleeve/ferrule! 

Note: order this item for models CI050000PD, CI05000BPP, CI070000PD, CI07000BPP.

Old Part Numbers: TF061300AVCylinder-to-Valve Plate Gasket. Remember to tighten the head bolts down to the appropriate torque spec when reinstalling the head.

Pressure switch, 135/175 PSI. Single-port w/ 1/4" compression unloader valve. Replace the pressure switch if the compressor no longer cuts in or cuts out at the designated pressure (PSI), if the unit...

Air compressor check valve, 3/4" Compression x 3/4" MPT with 1/8" FPT side port.  If the small unloader (bleeder) valve on or under your switch leaks constantly AFTER the unit shuts off, replace this...

Old Part Numbers: TF060300AVHead Gasket for the TF/TX series pumps. Replace if leaking or if the intercooler safety relief valve blows off.

16.5" CI Pump Flywheel, 1-Belt with Key for air compressors. Taper Bore - 1.32 to 1.51. Has now been changed to a single-groove flywheel. Will still work with two-groove motor pulley.

Air compressor pump air filter kit includes the canister assembly, filter element, bolts, washers, and wingnut. Note: Order this kit for CI0500 models and others. Replacing the pump's air filter...

Connecting rod assembly. Includes the needle bearing, insert bearings, bolts, and dipper. Used on many CI0500, CI0700, TF2001, TF2101, TF2111, and TF2912 air compressor pumps.

Old Part Numbers: BT008500AVAlso used on models CE720500FP, CE720600FP.

Note: order this item for models CI050000PD, CI05000BPP, CI070000PD, CI07000BPP. This is the newer style valve plate (uses preformed o-ring gaskets). Poor performance or air leaks out of the intake...

Old Part Numbers: ST074415AV, ST120200AV, ST073236AVIncludes six (6) screws.

Pump overhaul kit includes valve plate with preinstalled valves and o-ring seals, cylinder-to-crankcase gasket, and a complete piston ring set.

Old Part Numbers: 68-4-21/8" male NPT x 1/4" compression adapter for air compressor unloader/bleeder line. A very common adapter to attach the 1/4" OD unloader/bleeder line from the unloader valve on...

Old Part Numbers: ST070387AV-MAT1/4"-18 NPT x 2.5" long pipe nipple for air compressors. Don't forget to apply plumbers' (teflon) tape to the threads for a tight seal.Extra DetailsIf you have a...

Needle bearing for connecting rod (one used per rod).

Old Part Numbers: TF050100AV

Old Part Numbers: BG217000AJSquare Wire Air Compressor Belt Guard (Front).  If you need the back Belt Guard as well, order BG217100AV.

Old Part Numbers: BG217100AJNew OEM belt guard replacement (back). This is the base of the belt guard that fastens to the compressor. Protect your fingers from moving parts. OSHA required.

Smaller, high-pressure (HP) piston with rings. Stagger rings and hone cylinder prior to installing.

Bare Head for the pump, no Gaskets included. If you need the Gaskets, order the Complete Gasket Kit.

Larger, Low-Pressure (LP) Piston with rings. Stagger the rings and hone cylinder prior to installing.

New crankshaft assembly with ball bearings.

Used on models CE720500FP and CE720600FP.

Complete gasket kit for the in-line, twin-cylinder, two-stage "TF" series air compressor pump with o-ring-style head gaskets includes head gasket, cylinder-to-valve plate gasket, crankcase gasket,...

Old Part Numbers: TF202700AV

Old Part Numbers: GA016703AVReplacement Pressure Gauge, 300 psi, 2" Face, Back-Mount (1/4" male NPT).

Bare Cylinder for two-stage pump. Order any necessary gaskets separately.

(not shown) - Flywheel Key. 3/8" key

Bare intercooler tube fitting for pump. The o-rings, bolts, nut, and ferrule are not included. Order TF060402AJ if you need the kit including these parts.

Old Part Numbers: TF063501APUnloader Tube that runs from the Check Valve to the Pressure Switch.

7.5 HP, 3-Phase, 208/230 volt magnetic starter. Important: Electrical components, such as magnetic starters, motors, capacitors (etc.) cannot be returned for a refund

Old Part Numbers: MC301500AV, MC301500IP, MC033600AV, MC030900AV, MC030900SJ7.5 HP, 3 PHASE.