Old Part Numbers: 180421, 184218mm.

NOTE! This Filter will only fit 2HP models! Order part number 90227 for 1HP models. Click here for SKU 90227.Extra DetailsA clean air filter is essential to the performance of an air compress

1/4" male NPT to 8mm Fitting. Order one for each end of the 180421-1 Uploading Tube.

If your unit has a hard time restarting when trying to cycle, order this. If your pressure switch is leaking out of the small bleeder valve on the side (or located underneath), order this valve...

California Air Tools Regulator Manifold for air compressors. The regulator controls the amount of air in your air compressor hose. Replace this if you're not able to adjust the PSI to your hose or if...

1/4" Ball Valve Drain Cock for air compressors. Keep your tank from rusting. Replace this if it is leaking or will not work.

Also known as a "cold start" valve, this integral component releases air off of the piston and pump head after it shuts off, which allows the motor to start much more easily and efficiently. This...

Elbow fitting / adapter for air compressor. Used to change the direction of airflow.

Old Part Numbers: SRV250140Air compressor safety relief valve, 1/4" MPT, 140 PSI. If your valve leaks below the pressure listed on the side of the valve, replace this vital safety feature...

Old Part Numbers: 90393Air compressor pressure switch assembly. If the compressor doesn't cut in or cut out at the designated PSI, most likely the pressure switch is defective. NOTE: If your pressure...

2 HP Piston ring for air compressors. This tends to be a high wear part, especially if you are in a high particulate environment. Order the cylinder sleeve when buying this part as the two wear...

California Air Tools Cylinder O-Ring gasket. Note: For newer models with motor serial# ending in "-O".

Electromagnetism Valve for 110V units.

Old Part Numbers: 1804311-ft length of 6mm nylon tube for California Air Tools air compressors.

California Air Tools air compressor exhaust hose for 2HP models. Stainless steel braded fluid hose, 3/8" ID.

"T" fitting for the cold start valve. This valve installs into the pump head. The braided discharge tube threads into one end and the cold start valve is installed in the other.

1/4" Quick Connect for California Air Tools air compressors.

2HP Cylinder O-Ring Head Rubber Gasket. Note: For newer models with motor serial# ending in "-OT".

California Air Tools cushion foot

Exhaust Manifold Elbow for California Air Tools air compressors.

Old Part Numbers: MP218-O, MP2018-OThis is the o-ring seal for each end of the pump connecting hoses, which connects the two air compressor pump heads.

This is the fitting for the small M10 X 6mm uploading tube that routes to the on/off pressure switch.

Gassing Exhaust Valve for air compressors. If you have a loss of compression, replace this exhaust valve and the intake valve.

California Air Tools MP2012-O cylinder for air compressor repairs.  Replace the cylinder if it is damaged or worn, or if you are also replacing the compression ring. NOTE: For newer models with motor...

OEM replacement Pressure Gauge 2.0″ Face, 1/4" NPT Center Back-Mount, 0-180 PSI.

Smaller capacitor for 2 HP, 110V models rated at 90 uF. NOTE! For newer models with unit serial# ending in "-O". Please note: Capacitors can not be returned for a refund unless proven to be defective.

Old Part Numbers: PW2034Quick Coupler (Fitting) for 6mm tubes. Male thread on one end, quick-release fitting on the other for the tube.

A 10-foot section of 8mm tubing that is ideal for all AD, CAD, SPC, SPCAD, HDCADC, DCAD & DCADC models that require a long piece of tubing to support water drainage from the Automatic Drain Valve,...

This is the nylon hose in the intake port of the air intake filter.

Washer for the Cushion Foot.

Bolt for Cushion Foot.

Bare Valve Plate for 2 HP motors. Replace if damaged or pitted. Does not include valves.

California Air Tools Air Compressor Pump Replacement, Complete Assembly, Ultra Quiet, Oil-Free, 2 HP. Comes with: (1) capacitor, (2) air filters, and (4) shock struts. Oil-Free Pump = Cleaner air for...

This is the intake valve that installs on the bottom of the valve plate. Replace if broken or corroded.

Bare Pump Head. Both cylinders use the same pump head. NOTE: Does not include any gaskets/seals, order separately.

New OEM Manifold Assembly. Includes the Manifold, Regulator, Tank and Regulator Pressure Gauges, Safety Relief Valve, and Couplers. The regulator controls the amount of air in your air compressor...

1/4" NPT countersunk hex pipe plug for the head.

Steel Plug for the pump head.

California Air Tools air compressor nut for cushion foot.

2HP Shock Strut

NOTE! For newer models with motor serial# ending in "-O".

Old Part Numbers: Left Fan-CAT

SR-7K-2 Black Strain Relief

Power Cord with Plug for California Air Tools air compressors, 110V.

Protect your fingers by keeping the spinning fan covered with this fan cover.

Larger capacitor for 2 HP, 110V models rated at 150 uF. Please note: Capacitors can not be returned for a refund unless proven to be defective.

Old Part Numbers: No. 72B, NO. 72BBolt (only) for wheel.

The California Air Tools automatic drain valve long extension kit (110V / 60Hz) is designed to eliminate the need to manually drain water and condensate from the air compressor air tank. This kit...

Screw that holds on the fan cover to the pump. 2HP Fan Cover Screw

2HP Adjustment Stent