Old Part Numbers: K0058, K-0058, K0650, K-0650 Sears 919.16014, 91604, K-0650Compression ring replacement kit includes the cylinder, piston ring, retaining screw, o-ring, and head o-ring. Restores...

Old Part Numbers: KK-4835, CAC-118, 889124, 889125, 891125, AC-0788, CAC-1118, D25009, D25837, CAC1118, CAC118, CAC-249, CAC-249-1, A02743, K-0651, KK-5081, 889124 889125 891125 AC-0788 CAC-1118...

Old Part Numbers: CAC-1372Protect your pump from damage by keeping clean or replacing. Air Compressor Air Intake Filter for Many Single Cylinder Oil-less Pumps Part # D24233:Replaces CAC-1372<

Muffler for Single Cylinder units.

O-ring seal for air compressor valve plate, installs in between the cylinder and valve plate. Used with origina

Old Part Numbers: 5130038-00, 5130024-001/4" OD brass compression nut and sleeve for bleeder (unloader) tube for air compressors.

Bushing Filter Retainer. This bushing (retainer) keeps the air intake filter element in place.

Old Part Numbers: GA016300AV, GA016310AV, GA016303AV, GA016308AV, GA016313AVPressure Gauge. 0-300 PSI, 1/8" NPT, Right-mount, 1.625" face. Use Teflon tape on the threads when installing.

Order this if ordering valve plate or a new head.

Screw for the plastic motor/pump shroud.

Brass compression nut and sleeve for 3/8" OD tubes.

Air compressor compression ring, pre-formed. Note: After you install the ring on the piston rod, install the rod in the cylinder by inserting the rod from the top of the cylinder and pull it down...

Isolator for the pump/motor assembly base. NOTE: To replace all of them you will need to order a quantity of 3. Keep your compressor from vibration damage and replace if any are missing.

Universal Regulator: 4-port, two 1/4" FPT ports, and two 1/8" FPT ports (gauges sold separately here). The regulator controls the amount of air in your air compressor hose. Replace this if you're not...

Hex Nut for the pump head. The discharge tube attaches to this part. Order the required AC-0781 O-ring Seal as well if needed.

Old Part Numbers: AB-ACG18Saddle mount cup for the motor/pump feet. This installs on the mounting feet of the motor/pump assembly and keeps it from vibrating, as well as reducing noise.

Old Part Numbers: SRV187150, SRV187-1/8Air compressor safety valve, 150 PSI, 1/8" male NPT. If your valve leaks below the pressure listed on the side of the valve, replace this vital safety feature.

Old Part Numbers: 68-4-21/8" male NPT x 1/4" compression adapter for air compressor unloader/bleeder line. A very common adapter to attach the 1/4" OD unloader/bleeder line from the unloader valve on...

Screw that fastens the front and back of the belt  guard to each other, and to the compressor base. THD FORMING

Old Part Numbers: 5130940-00, SSF-8080-ZNFlange nut to attach the wheel to the air tank.

Screw to fasten the handle to the compressor base.

Screw, .250-20 x 1.25" U. This is one of the screws for the pump head; also used to attach the saddle mount cup/foot to the base of the pump.

Old Part Numbers: SSF-3158-1This is the screw that holds down the piston cover, on the top of the piston.

Old Part Numbers: 60-6Air compression sleeve/ferrule for 3/8" OD tube.